Bedienungsanleitung Panasonic AG-HPX 300P (Seite 143 von 166) (Englisch)

597937

143

Zoom out

Zoom in

Vorherige Seite

1/166

Nächste Seite

143

Chapter 8 Connecting to External Devices

Select OPERATION  FORMAT (HDD) in the

menu and use a cursor button and the SET

button to select YES.

• Select YES in the conﬁrmation message that

appears again to start hard disk drive formatting.

• Handled as a “TYPE S” hard disk drive after

formatting.

 NOTE

All data on a hard disk drive is deleted when the disk is

formatted. It is not possible to select part of a partition

to delete.

Writing to hard disk drive

Switch to the USB host mode.

For details, refer to [Switching to USB Host Mode]

(page 140).

Connect a hard disk drive via USB.

If the hard disk drive has not been formatted by

the camera, format it according to the instructions

provided in [Formatting Hard Disks] (page 142).

Insert a P2 card.

Press the THUMBNAIL button to open the

thumbnail screen.

Press the THUMBNAIL button and select HDD

 EXPORT from the thumbnail menu and

specify the slot of the P2 card with the data you

want to write to the hard disk drive.

Select YES.

• This starts the write process.

• A progress bar appears during the write process.

To interrupt writing, press the SET button.

Selecting YES in the cancel conﬁrmation that

appears will stop the write process.

• COPY COMPLETED! announces the end of the

write process.

 NOTE

• To turn off the verify phase in a write operation, select

HDD  SETUP in the thumbnail menu and set VERIFY

to OFF. This speeds up the write time but does not

verify the written data.

• Selecting ALL SLOT writes the data on all inserted P2

cards inserted in the camera to the hard disk drive.

 NOTE

• A TYPE S hard disk drive can write data in card units. Up

to 23 P2 cards can be saved to a hard disk drive.

The P2 card data recorded on a hard disk drive are

recognized as separate drives.

• To write P2 cards with bad clips, it is a good idea to repair

these clips before writing them to a hard disk drive.

• Ending a recording during the verify phase will end writing

of data from the P2 card to the hard disk drive.

Writing back data to P2 cards

This allows you to select a clip from the hard disk drive and

write it back to a P2 card.

Switch to the USB host mode.

For details, refer to [Switching to USB Host Mode]

(page 140).

Connect a hard disk drive via USB.

Insert the P2 card to which data will be written

back to.

Press the THUMBNAIL button, select HDD 

EXPLORE from the thumbnail menu, move to

the partition with the data that will be read and

press the SET button.

Select the clip to be written to the P2 card from

the thumbnail on the hard disk drive.

Press the THUMBNAIL button, select

OPERATION  IMPORT  SELECTED CLIPS

from the thumbnail menu and select the slot of

the P2 card to write the data to.

Select YES.

• This starts the data write to the P2 card.

• When the write process ends, “COPY

COMPLETED!” appears.

 NOTE

• When clips are selected for writing, verify is not performed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic AG-HPX 300P Seite 143

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info