Bedienungsanleitung Panasonic AG-HVX 200AP (Seite 122 von 138) (Englisch)

597941

122

Zoom out

Zoom in

Vorherige Seite

1/138

Nächste Seite

122

Displays

Something is wrong with

the time code display.

• The time code display may not register a regular count if a tape is

played in the reverse slow mode. This is normal.

—

The remaining tape display

differs from the actual

amount of tape remaining.

• The remaining tape is not displayed accurately if you shoot

continuously for periods of less than 30 seconds.

—

• The display may show 2 to 3 minutes less than the actual time

remaining on the tape.

—

Playback

Cannot play even when I

press the play button.

• Make sure the MCR/VCR lamp is on (press the mode button).

No kind of playback operation can be performed unless this lamp is

on.

P 63, 64

Cannot play back P2 cards

or tapes.

• Make sure the MEDIA switch is in the correct position.

If not, set it to the P2 or TAPE position.

P 63, 64

Mosaic-like noise appears

when I cue or review a tape.

• This noise is inherent to digital video technology. This is normal. —

Images do not appear on

the television even though

I have connected the

camera-recorder properly.

• Make sure the input selector on your television is set to video input.

Read the television’s instructions carefully and select the correct

video input connector for the camera-recorder.

—

• When a component video cable is connected, video signals are not

output from the VIDEO OUT and S-VIDEO OUT connectors.

P 80

The playback images are

not displayed clearly.

• The camera-recorder’s heads may be dirty.

Images will not be displayed clearly if the heads are dirty.

—

Cannot hear any sound

from the camera-recorder’s

speaker.

• You may have turned down the camera-recorder’s volume control

too far.

Adjust the volume level using the AUDIO MON/ VAR button+.

P 76

I can hear two sets of

sound.

• You may have selected “MIX” as the 32K(12bit) AUDIO setting in

the PLAYBACK FUNCTION screen.

P 110

• If you perform audio dubbing on a tape that was recorded with 32K

(12bit) selected as the AUDIO REC setting in the RECORDING

SETUP screen, you will hear the sound heard during recording

and that of the audio dubbing. You can also listen to each sound

separately.

P 107

When I performed audio

dubbing, the original sound

was erased.

• If you perform audio dubbing on a tape that was recorded with 48K

(16bit) selected as the AUDIO REC setting in the RECORDING

SETUP screen, you will hear the sound heard during recording and

that of the audio dubbing. To leave the original sound intact, make

sure that 32K (12bit) is selected when you shoot.

P 107

Cannot perform hot swap

playback.

• This unit does not support hot swap playback.

To replace one card with another during dubbing, stop the dubbing

first, and upon completing the replacement, resume it.

P 88

Before calling for service (continued)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic AG-HVX 200AP Seite 122

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info