502343
41
Zoom out
Zoom in
Vorherige Seite
1/52
Nächste Seite
RQT9378
41
On the unit’s display Page
F99 The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch
the unit to standby for 3 seconds. Now press [POWER Í/I] on the main unit
again to turn the unit on.
HDMI ONLY Some BD-Video discs can only be output with HDMI.
NET Displays while VIERA CAST is starting up.
No PLAY There is a viewing restriction on a BD-Video or DVD-Video. 32
No READ The media is dirty or badly scratched. The unit cannot play.
PLEASE WAIT The unit is carrying out internal process. This is not a malfunction. You cannot
operate the unit while “PLEASE WAIT” is displayed.
When connected to TV(VIERA) with HDAVI Control 4, and power supply is turned
off by the “Auto power stand-by” function on the TV side.
REMOVE The USB device is drawing too much power. Remove the USB device. 19
SET
(“ stands for a number.)
The remote control and main unit are using different codes. Change the code on
the remote control.
Press and hold [OK] and the indicated number button at the
same time for more than 5 seconds.
36
UNFORMAT You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL
or DVD-RW (DVD-Video format).
UNSUPPORT You have inserted a media the unit cannot play.
You tried to operate with a non-compatible USB device.
6, 7
7
U59 The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block the
cooling fan on the rear of the unit.
U72
U73
The HDMI connection acts unusually.
–The connected equipment is not HDMI compatible.
–Please use HDMI cables that have the HDMI logo (as shown on the cover).
–The HDMI cable is damaged.
H or F There is something unusual. (The service number displayed after H and F
depends on the unit’s condition.)
Check the unit using the troubleshooting guide. If the service number does not
disappear, do the following.
1 Disconnect the plug from the AC outlet, wait a few seconds, then reconnect it.
2 Press [POWER Í/I] to turn the power on. (The unit may be fixed.)
If the service number does not disappear despite doing the above, request
service from the dealer. Inform the dealer of the service number when requesting
service.
42–44
START The system is being restarted during the firmware update. Please do not turn off
power.
16
UPD/ The firmware is being updated. 16
FINISH The firmware update is complete. 16
Reference
RQT9378~Body_mst.fm 41 ページ 2008年12月25日 木曜日 午後3時24分
41

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic DMP-BD60 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Panasonic DMP-BD60

Panasonic DMP-BD60 Bedienungsanleitung - Deutsch - 132 seiten

Panasonic DMP-BD60 Bedienungsanleitung - Holländisch - 104 seiten

Panasonic DMP-BD60 Bedienungsanleitung - Italienisch, Spanisch, Spanisch - 132 seiten

Panasonic DMP-BD60 Bedienungsanleitung - Schwedisch - 104 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info