Bedienungsanleitung Panasonic EY 6432 (Seite 6 von 59) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

78273

Zoom out

Zoom in

Vorherige Seite

1/59

Nächste Seite

— 6 —

Read the Safety Instructions booklet

and the following before using.

I. ADDITIONAL

SAFETY RULES

1) Be aware that this tool is always in an operat-

ing condition, since it does not have to be

plugged into an electrical outlet.

2) When drilling or driving into walls, floors, etc.,

“live” electrical wires may be encountered.

DO NOT TOUCH THE CHUCK OR ANY

FRONT METAL PARTS OF THE TOOL! Hold

the tool only by the plastic handle to prevent

electric shock in case you drill or drive into a

“live” wire.

3) If the bit becomes jammed, immediately turn

the main switch off to prevent an overload,

which can damage the battery pack or motor.

Use reverse motion to loosen jammed bits.

4) Do NOT operate the Forward/Reverse lever

when the main switch is on. The battery will

discharge rapidly and damage to the unit

may occur.

5) During charging, the charger may become

slightly warm. This is normal. Do NOT charge

the battery for a long period.

6) Use only a dry, soft cloth to wipe the unit. Do

NOT use a damp cloth, thinner, benzine, or

other volatile solvents for cleaning.

7) When storing or carrying the tool, set the Forward/

Reverse lever to the center position (switch lock).

8) Do not strain the tool by holding the speed

control trigger halfway (speed control mode)

so that the motor stops.

9) Do not operate the speed selector switch

(LOW-HIGH) while pulling on the speed con-

trol trigger. This can cause the rechargeable

battery to wear quickly or damage the inter-

nal mechanism of the motor.

10) Young children should be supervised to

ensure that they do not play with the appli-

ance.

11) Wear ear protectors when using the tool for

extended periods.

II. ASSEMBLY

Attaching or removing bit

Note: When attaching or removing a bit, be sure

to set the Forward/Reverse lever to its cen-

ter position (switch lock).

This tool is equipped with a keyless drill chuck.

1) Attachment

Insert the bit and turn the lock collar clock-

wise (looking from the front) to tighten. (Fig.

2) Removal

Turn the lock collar counterclockwise (looking

from the front), then remove the bit. (Fig. 3)

3) Storage

Keep the bit in bit holder when not in use.

Remove the battery pack to expose the bit

storage compartment inside the handle hous-

ing.

Bits up to 50 mm (1-31/32 inch) long can be

stored here. (Fig. 4)

Note: If excessive play occurs in the chuck,

secure the drill in place and open the

chuck claws by turning the lock collar and

tighten the screw (left-handed screw)

with a screwdriver by turning it counter-

clockwise (viewed from the front). (Fig. 5)

Attaching or removing battery pack

1. To connect the battery pack:

Insert the battery pack. It snaps into place to

indicate proper connection.

2. To remove the battery pack:

Press the two buttons on the sides of the bat-

tery pack. Slide the battery pack out of the tool

body.

EY6405(EU).book Page 6 Wednesday, June 15, 2005 7:14 PM

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY 6432 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info