Bedienungsanleitung Panasonic EY3552 (Seite 10 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502386

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

11) Be careful not to drop Metal Cutter.

12) Never swing Metal Cutter.

13) Never cover the ventilation slots, and keep

them free from dust or other material.

14) Do not clamp Metal Cutter in a vise. Never

cut with Metal Cutter held upside down in a

vise. This is extremely dangerous and can

lead to serious accidents.

15) Never wear knitted gloves.

16) Be sure no one is below when using Metal

Cutter in high locations.

17) Do not touch the blade immediately after

operation. It may be hot and could burn

your skin.

18) Do not touch material after it has been cut.

Cut material may be very hot.

19) Do not use cutting oil. This use of cutting oil

may cause a fire.

20) Do not cut workpieces covered or stained

with gas, oil, solvents, thinners, etc.

Exposure to these materials may damage

the transparent guard.

21) Do not remove the transparent and lower

guards. If the transparent and lower guards

is damaged or missing, return tool to

authorized service center for replacement.

22) Do not start the blade when in contact with

workpiece. Wait for blade to reach full speed

before beginning cut.

Symbol

Meaning

Volts

Direct current

No load speed

··· / min

Revolutions or reciprocations

per minute

Amperes

III. SETTING UP

Charging Battery Pack EY9251

Charge the battery pack when the cutting speed

becomes too slow for effective cutting.

If you have two battery packs, you can use one to

continue working while charging the other one.

NOTE:

When you charge the battery pack for the first

time, or after prolonged storage, charge it for

about 24 hours to bring the battery up to full

capacity.

Battery charger (EY0110)

1. Plug the charger into the AC outlet.

NOTE:

Sparks may be produced when the plug is

inserted into the AC power supply, but this is

not a problem in terms of safety.

2. Insert the battery pack firmly into the charger.

Battery

pack

To AC

outlet

Battery

charger

3. During charging, the charging lamp will be lit.

When charging is completed, an internal elec-

tronic switch will automatically be triggered to

prevent overcharging.

• Charging will not start if the battery pack

is warm (for example, immediately after

heavy-duty operation).

The orange standby lamp will be lit until the

battery cools down. Charging will then begin

automatically.

4. When charging is completed, the charging

lamp will start flashing quickly in green color.

5. When in any of the conditions that battery

pack is too cool, or the battery pack has not

been used for a long time, the charging lamp

is lit. In this case, charging takes longer to fully

charge the battery pack, than the standard

charging time.

• If a fully charged battery pack is inserted

into the charger again, the charging lamp

lights up. After several minutes, the charg-

ing lamp may flash quickly to indicate the

charging is completed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY3552 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info