Bedienungsanleitung Panasonic EY3552 (Seite 12 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502386

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

Inserting Battery Pack

CAUTION:

Before inserting battery pack, check that the

power switch in the Metal Cutter actuates properly

and returns to the “OFF” position when released.

1.To insert the battery pack: (See Fig.2)

Slide the battery pack in place at the rear of

the metal cutter. The battery should snap into

place. If the battery is loose, it has not been

properly connected.

2.To remove the battery pack:

Press the two tabs on the sides of the battery

pack. Slide the battery pack out of the metal

cutter body.

IV. OPERATION

Before Using Metal Cutter

This tool is intended for cutting unhardened fer-

rous metal and nonferrous metal. Refer to the

“Accessories” section for a list of blades to be

used for the proper applications of this tool. The

following precautions must be followed to reduce

the risk of injury;

•Do not cut stacked materials. Cut one piece at a

time.

•Do not cut hardened steel.

•Cut materials with the wider edge of the shoe

over the clamped side of the material.

•Do not touch the saw blade, workpiece, or cutting

chips with bare hands immediately after cutting;

they may be hot and could burn skin.

Each time you use the metal cutter, you must

make sure it is in good operating condition.

Use the following checklist:

1.Is the blade installed in the correct direction?

The arrow on the blade must point in the same

direction as the arrow on the upper blade

cover.

2.Is the blade installed properly?

Make sure the hex bolt is tightened securely.

(See Fig.12)

3.Does the blade look alright?

Replace the blade immediately if there are any

cracks in it or if any teeth are broken.

4.Does the lower guard close properly?

WARNING

To avoid injury, do not use the metal cutter if

the lower guard does not close quickly over

the blade.

5.Is the transparent guard securely installed?

6.Is the battery pack charged and inserted firmly

to the metal cutter?

7.Is the depth adjustment lever for cutting

securely tightened?

8.Is the workpiece securely clamped on a saw

horse or bench?

Using Metal Cutter

CAUTION:

To reduce the risk of injury read the Safety

Instructions at the front of this manual before using

the metal cutter.

WARNING

To reduce the risk of injury, wear safety goggles

or glasses with side shields.

Follow these steps:

Hold the metal cutter with both hands. (See

Fig.4) Do not attempt to remove cut material

when blade is moving.

1.Line up the sight line on shoe with your cutting

line. (See Fig.3)

Alignment with cutting line

• Use the notch as guide to establish cutting

position. Align the notch with cutting line.

As the cutting position may differ depending on

the blade, do a trial cut beforehand.

2.Press the switch lock lever down, then

squeeze the power switch to start the motor,

and then release the switch lock lever.

CAUTION:

• Check that the switch lock lever works.

If power switch can be activated without

depressing the switch lock lever, discontinue

use immediately. Take the tool to an author-

ized service center.

• Always hold the handle with one hand and the

front grip with the other. (See Fig.4) Maintain a

firm grip and depress the switch fully.

• The blade should not touch the cutting mate-

rial before you start the motor. Wait until the

blade reaches full speed before starting a cut.

• This tool has no provision to lock the power

switch in the “ON” position, and you must not

attempt to secure it in the “ON” position.

3.Start cutting when the blade reaches full

speed.

4.During cutting, keep your cutting line straight.

Move the metal cutter forward at a steady

speed, while looking at the tip of the blade

through the transparent guard.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY3552 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info