Bedienungsanleitung Panasonic EY3552 (Seite 13 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502386

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

WARNING

• To prevent dangerous kickback, keep the

shoe of the metal cutter flat on the surface of

the material being cut.

• Never force the cutter. Use light and continu-

ous pressure.

5.If the motor starts to feel too warm, stop cut-

ting. Let the metal cutter cool down before

continuing work.

6.It is always a safe practice to remove the

battery pack after use and before storing the

metal cutter.

Cutting depth adjustment

•Remove battery pack.

•Loosen the depth adjustment lever by pushing it

and adjust the cutting depth.

Tighten the depth adjustment lever securely by

lifting it up towards the motor housing at the

desired cutting depth. (See Fig.5)

Rip fence (EY3500B7727)

(Available as an accessory, not included)

Rip fence is convenient for rip cuts and repeated

cuts of uniform width.

•Remove battery pack.

•Insert rip fence and adjust cutting width. (See

Fig.6)

•Fasten screw securely to fix rip fence.

For Proper Use (Further Detail)

WARNING

To prevent the risk of serious personal injury:

l It is important to use an appropriate device

to hold the material being cut properly, and

to hold the cutter firmly with both hands to

prevent loss of control which could cause

personal injury.

• Figure 7 shows proper cutting position.

• Note that hands are kept away from cutting

area.

• Make sure bystanders are away from work

area and from underneath of workpiece.

• When cutting, do not try to hold the material

with your hand.

Cutting large sheets;

Support large sheets. Be sure to set the depth

of the cut so that you only cut through the

workpiece, not through the supports. (See

Fig.8)

Large sheets sag or bend if they are not

correctly supported. If you attempt to cut

without leveling and properly supporting the

workpiece, the blade will tend to bind, causing

kickback. (See Fig.9)

• Don’t support the material away from the

cut.

Cutting thin or corrugated materials;

Cut thin and corrugated materials at least

1" from the edge of the workpiece to avoid

injury or damage to the tool caused by thin

strips of metal being pulled into the upper

guard.

•Use sharp blades only. Clean and sharp

blades minimize stalling and kickback.

WARNING

To prevent the risk of serious personal injury:

• When making an incomplete cut or cutting

is interrupted, or blade is binding or cutter is

stalling; release the power switch immediately

and hold the cutter motionless in the material

until the blade comes to a complete stop.

• To avoid kickback, never attempt to remove

the cutter from the work or pull the cutter

backward while the blade is in motion. Make

sure the blade has come to a complete stop,

then remove cutter from cut.

• To resume cutting, start metal cutter, allow

the blade to reach full speed, reenter the cut

slowly and resume cutting.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY3552 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info