Bedienungsanleitung Panasonic EY3552 (Seite 14 von 124) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Schwedisch, Norwegisch, Finnisch)

502386

Zoom out

Zoom in

Vorherige Seite

1/124

Nächste Seite

1.Place the wider part of the shoe on the part of

the work piece which is solidly supported (See

Fig.10), never on the section that will fall off

when the cut is made. (See Fig.11)

Hold the cutter firmly to prevent loss of control.

Working carelessly can cause severe personal

injury.

2.Make sure the blade stops.

Even though your metal cutter has a brake,

before setting the metal cutter down, make

sure the blade has come to a complete stop

and the lower guard has closed.

3.Do not use if anything seems unusual. Remove

battery pack immediately.

If the metal cutter body becomes very hot, or

does not work properly, remove the battery

pack and do not use. Have it checked by an

authorized service center.

WARNING

To prevent the risk of serious personal injury

or fire, do not try to repair the metal cutter

by yourself. Never disassemble or modify the

metal cutter body. There are no user-repair-

able parts inside.

4.NEVER ALLOW THE CUTTER TO COME IN

CONTACT WITH YOUR BODY.

After completing a cut, do not allow the cutter

to brush against your leg or side.

Since the lower guard is retractable, it could

catch on your clothing and expose the blade.

Keep clothing away from metal cutter. Be

aware of the exposed blade sections that exist

in both the upper and lower guard areas.

WARNING

Because cutting metal creates sparks;

• Always use safety goggles.

• Do not use metal cutter near any flammable

substance or in an area where flammable

substances are used. Fire and burn injury

could result.

5.Never engage the spindle lock while blade is

running, or engage in an effort to stop the tool.

Never turn the switch on when the spindle lock

is engaged. Serious damage to your metal cut-

ter will result.

V. MAINTENANCE

WARNING

To avoid severe personal injury, always

remove the battery pack from the metal cutter

before starting any maintenance procedure.

CAUTION:

To assure product SAFETY and RELIABILITY,

servicing should be performed by an authorized

service center. Always insist on genuine Panasonic

replacement parts.

Removing Blade

CAUTION:

The blade will be hot right after cutting. Be sure to

let the blade cool down before removing it.

Follow these steps:

1.Remove the battery pack from the metal cutter.

2.Hold the spindle lock button down. This pre-

vents the blade from rotating.

3.Use the provided hex wrench to loosen the hex

bolt.

NOTE:

Keep the hex wrench in the storage slot on the

metal cutter’s body when not using it.

4.Remove the hex bolt and outer washer.

5.Use the lower guard lift lever to retract (open)

the lower guard.

6.Carefully remove the blade.

7.Clean the metal cutter if necessary.

CAUTION:

Be careful to avoid cutting your hands on the

blade.

• When disposing of a blade, secure it inside

heavy or corrugated paper. This will help pre-

vent anyone from being cut by the discarded

blade.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic EY3552 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info