Bedienungsanleitung Panasonic NVMD9000EN (Seite 7 von 40) (Englisch)

627468

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Before

Use

-41-

Attaching the Microphone to the

Movie Camera

Attach the microphone to the Movie

Camera shoe.

1) Loosen the Shoe Lock.

2) Attach the microphone.

3) Firmily tighten the Shoe Lock.

Connect the Stereo Mini-Plug Cord to the

[EXT MIC]

(28)

socket.

≥You can adjust the microphone angle within

the range shown in the figure.

≥Hold the Shoe Lock portion when attaching

and removing the microphone.

≥Be sure to set the Movie Camera power to

[OFF] before connecting the microphone.

Using the External Stereo

Microphone

Set the [OFF/MONO/STEREO] Switch

(53)

to [MONO] or [STEREO].

[OFF]: Turn off the microphone power.

[MONO]: Records sound in front of the

movie camera in monaural.

[STEREO]: Records sound in a wide area in

stereo.

≥Although you can change the setting of the

[OFF/MONO/STEREO] Switch while

recording, the sound of the switch being

changed may be recorded. Pause your

recording before changing the setting of this

switch.

≥When the [OFF/MONO/STEREO] Switch is

changed from [OFF] to [MONO] or [STEREO],

the [BATTERY] Lamp

(54)

will light temporarily

if there is still plenty of power in the battery. If

the [BATTERY] Lamp does not light

temporarily, replace the battery with a new

one.

EXT MIC

(28)

OFF

STEREO

MONO

BATTERY

OFF ON

WIND CUT

(53) (54)

(55)

Changing the [WIND CUT OFF/ON] Switch

The microphone is equipped with a wind shield

that is designed to cut down wind noise, but

when the wind is so strong that even the wind

shield is not adequate to keep down the noise,

set the [WIND CUT OFF/ON] Switch

(55)

[ON] to further reduce the wind noise.

[OFF]: The microphone should usually be used

with this position.

[ON]: Set the [WIND CUT OFF/ON] Switch to

this position to reduce wind noise or

bass noise.

≥Although you can change the setting of the

[WIND CUT OFF/ON] Switch while recording,

the sound of the switch being changed may be

recorded. Pause your recording before

changing the setting of this switch.

≥For other notes concerning this item, see

-68-

The Remote Controller

Inserting a Button-type Battery

Before using the Remote Controller, insert the

supplied button-type battery.

While pressing the Stopper 1, pull out the

Battery Holder.

Insert the button-type battery with the (i)

marking facing upward.

Insert the Battery Holder into the Remote

Controller.

≥When the button-type battery is exhausted,

replace it with a new CR2025 battery. (A

battery is normally expected to last about

1 year. However, it depends on operation

frequency.)

≥Make sure to match the poles correctly when

inserting the battery.

CAUTION

Danger of explosion if battery is incorrectly

replaced. Replace only with the same or

equivalent type recommended by the equipment

manufacturer. Discard used batteries according

to manufacturer’s instructions.

WARNING

Risk of fire, explosion and burns. Do not

recharge, disassemble, heat above 100xC or

incinerate. Keep the Button-Type battery out of

the reach of children. Never put Button-Type

battery in mouth. If swallowed call your doctor.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic NVMD9000EN Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info