Bedienungsanleitung Panasonic NVMD9000EN (Seite 8 von 40) (Englisch)

627468

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Before

Use

-42-

Using the Remote Controller

Direct the Remote Controller to the

Remote Control Sensor

(3)

of the Movie

Camera and press an appropriate button.

≥Distance from the Movie Camera: Within

approximately 5 metres

≥Angle: Within approximately 15o in the

vertical and horizontal directions from the

central axis

≥The above operative ranges are for indoor

use. Outdoors or under strong light, the Movie

Camera may not operate properly even within

the above ranges.

≥Within a 1-metre range, you can also use the

Remote Controller on the LCD Monitor side of

the Movie Camera.

Selecting Remote Controller Modes

When 2 Movie Cameras are used

simultaneously, they can be operated

individually by selecting different Remote

Controller Modes.

≥If the Remote Controller Mode of the Movie

Camera and that of the Remote Controller do

not match, [REMOTE] Indication is displayed.

Setup on the Movie Camera:

Set [REMOTE] on the [OTHER FUNCTIONS]

Sub-Menu to the desired Remote Controller

Mode. (

-45-

)

Setup on the Remote Controller:

[VCR1]:

Press the [D] Button and [∫] Button

simultaneously. 1

[VCR2]:

Press the [E] Button and [∫] Button

simultaneously. 2

≥When the battery in the Remote Controller is

replaced, the mode is automatically reset to

[VCR1] Mode.

Power Supply

Using the AC Adaptor

1 Connect the AC Mains Lead to the AC

Adaptor and the AC mains socket.

15˚

(3)

INDEX INDEX

SELECT

STOP

∫

STILL ADV

PAU SE

STILL ADV

61 5

;

DC IN 7.9V

(37)

≥The AC Mains Lead’s outlet plug does not fit

entirely into the AC Adaptor socket. A gap

will remain as shown 1.

Connect the DC Input Lead to the [DC IN]

Socket

(37)

on the Movie Camera.

Connect the DC Input Lead to the AC

Adaptor.

≥Before connecting or disconnecting the

power supply, set the [OFF/ON] Switch on

the Movie Camera to [OFF] and make sure

that [CAMERA/VCR] Lamps is not lit.

Using the Battery

Before use, fully charge the Battery.

Attach the Battery to the AC Adaptor and

charge it.

≥Since the Battery will not be charged when

the DC Input Lead is connected to the AC

Adaptor, disconnect it from the AC Adaptor.

≥The [POWER] Lamp and [CHARGE] Lamp

lights up, and charging starts.

≥When the [CHARGE] Lamp goes off,

charging is completed.

Attach the charged Battery to the Movie

Camera.

Disconnecting the Power Source

Set the [OFF/ON] Switch

(50)

to [OFF] and,

disconnect the DC Input Lead or while pressing

the [PUSH] Button

(35)

, slide the Battery

upward to disconnect it.

Using the Car Battery Charger

If you use the Car Battery Charger (VW-KBD2E;

optional), you can supply power to the Movie

Camera and charge the battery inside your car.

For further information, refer to the instruction

manual of the Car Battery Charger.

Be sure to start the car engine before you

connect the Car Battery Charger, otherwise the

fuse may blow.

≥For other notes concerning this item, see

-64-

PUSH

OFF ON

(35)

(50)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic NVMD9000EN Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info