Bedienungsanleitung Panasonic PT-DZ21KE (Seite 105 von 179) (Englisch)

511534

105

Zoom out

Zoom in

Vorherige Seite

1/179

Nächste Seite

[PROJECTOR SETUP] menu

ENGLISH - 105

Settings



Error details

Error message Remedy

[Exceed maximum

number of projectors.]

Set no more than eight

projectors in one group.

Use a computer and

the dedicated “Multi

Projector Monitoring &

Control Software”

connect nine or more

projectors.

[Please check the

COMMAND CONTROL

setting.]

Set the on-screen menu

[NETWORK CONTROL]

[COMMAND CONTROL]

to [ON] for the projector

in error.

Set the [NETWORK

CONTROL] [COMMAND

PORT] of all projectors

to be connected to the

same value.

[Please check the

USER NAME and

PASSWORD in the

COMMAND CONTROL

setting.]

Set the same character

string to the [User

name] and [Password]

that has Web control

administrator rights

for all projectors to be

connected.

[Cannot apply

BRIGHTNESS

CONTROL. Please

check projector status.]

The projector is in

standby status. Switch

on the projector.

[Brightness Sensor

Error]

There is a problem with

the luminance sensor.

If the problem is not

corrected by turning off

the power and turning it

on again, consult your

dealer.

*1: “Multi Projector Monitoring & Control Software” is included

in the attached CD-ROM.

Note

Check the following when a projector to be

connected is not listed.



Is there a device on the network with the same IP

address?



Is a LAN cable connected correctly? (



page 126)



Is the projector subnet identical?



Is [LINK] set to the same group?

To change a projector name, refer to [NETWORK

SETUP] (



page 125), or [Network cong] page

(



page 133).



When [MODE] in [BRIGHTNESS

CONTROL SETUP] is [PC]

0(18

5(7851

02'(

352-(&725

%5,*+71(66&21752/67$786

(1) Displays the name of the projector in question.

(2) Uses color to display status.

Green

There is margin for brightness correction.

Yellow

There is less margin for brightness correction.

Red: An error occurred in luminance control.

■

Example steps to adjust

luminance control

The steps exemplify an adjustment to link the

brightness of eight projectors connected in a network.

1) Use a LAN cable to connect all

projectors to a hub. (



page 126)

2) Switch on all projectors.

3) Set [LAMP SELECT] to either [DUAL]

or [SINGLE] for all projectors.

4) Set [MODE] in [BRIGHTNESS

CONTROL SETUP] to [OFF] and

[APPLY].

5) Set [SUBNET MASK] of the projectors

to the same value, and [IP ADDRESS]

of each projector to a different value

so that the network can communicate.

6) Wait at least eight minutes until the

lamp brightness becomes steady.

7) Set all items in the [PICTURE] menu of

all projectors to the same values.

8) To match colors, adjust [COLOR

MATCHING].

9) Display the internal test patterns of all

projectors in “completely white”.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DZ21KE Seite 105

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DZ21KE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info