Bedienungsanleitung Panasonic PT-DZ21KE (Seite 106 von 179) (Englisch)

511534

106

Zoom out

Zoom in

Vorherige Seite

1/179

Nächste Seite

[PROJECTOR SETUP] menu

106 - ENGLISH

Settings

10)

Set [BRIGHTNESS CONTROL GAIN]

of all projectors to 100%.

11)

Set [BRIGHTNESS CONTROL GAIN]

of the darkest projector to 90%.

12)

Adjust [BRIGHTNESS CONTROL

GAIN] to match the [BRIGHTNESS

CONTROL GAIN] set to 90% of the

other projectors.

13)

Set [MODE] in [BRIGHTNESS

CONTROL SETUP] of all projectors to

[AUTO], and [LINK] to [GROUP A].

14)

Select [APPLY] in [BRIGHTNESS

CONTROL SETUP] on all projectors

and press the <ENTER> button.



Luminance control starts.

Note

Brightness is automatically corrected each time the

lamp blinks when the power is switched on or off.

Adjust luminance control again when variation in

brightness has increased or a lamp is replaced.

[STANDBY MODE]

Set the power consumption during the standby.

1) Press



to select [STANDBY MODE].

2) Press

󱚣󱚤

to switch [STANDBY

MODE].



The setting will change as follows each time

you press the button.

[NORMAL] [ECO]

Note

When set to [ECO], network functions and <SERIAL

OUT> terminal, and some RS-232C commands are

not available during standby. The lighting for the

connecting terminals and control panel does not

turn on.

When an error or warning occurs, a self diagnosis

is displayed on the control panel regardless of the

[STANDBY MODE] setting. (



page 25)

When set to [ECO], the time taken to start display

may be approximately ten seconds slower than

compared to when set to [NORMAL].

[SCHEDULE]

Set the command execution schedule for each day of

the week.

1) Press



to select [SCHEDULE].

2) Press

󱚣󱚤

to switch [SCHEDULE].



The setting will change as follows each time

you press the button.

[ON] [OFF]

Note

If [SCHEDULE] is set to [ON], the setting for

[STANDBY MODE] is automatically set to

[NORMAL] and cannot be changed. Even if

[SCHEDULE] is then set to [OFF] when in this

state, the setting of [STANDBY MODE] remains at

[NORMAL].

■

How to assign a program

3) Select [ON] in Step 2), and press the

<ENTER> button.



The [SCHEDULE] screen is displayed.

4) Select and assign program to each day

of week.



Press



to select the day of week, and press

󱚣󱚤

to select a program number.



You can set the program from No.1 to No.7. “-

- -” indicates that the program number has not

been set yet.

■

How to set a program

You can set up to 16 commands to each program.

3) Select [ON] in Step 2), and press the

<ENTER> button.



The [SCHEDULE] screen is displayed.

4) Press



to select [PROGRAM EDIT].

5) Press

󱚣󱚤

to select a program number

and then press the <ENTER> button.

6) Press



to select a command

number and press the <ENTER>

button.



You can change the page using

󱚣󱚤

7) Press



to select [TIME] and press

the <ENTER> button.

8) Press

󱚣󱚤

to select hour and minute,

and press



or the number (<0> to

<9>) buttons on the remote control

to set a time, and press the <ENTER>

button.

9) Press



to select [COMMAND].

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic PT-DZ21KE Seite 106

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic PT-DZ21KE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info