Bedienungsanleitung Panasonic SAXR55 (Seite 21 von 28) (Englisch)

608302

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

RQT7994

ConnectionsSettingsBasic Operations Before useOperationsReference

Receiver settings

Advanced

• Any changes to settings remain as set even if the power is turned off.

áPage 24 “Multi control menus and factory settings”.

Use the MULTI CONTROL menus to change the settings.

Set the size so that the speakers can adequately reproduce the bass range.

The following are set automatically.

• When you set “FRONT ” to “SMALL ”, “SUB-WFR ” is set to “YES ”.

• When you set “SUB-WFR ” to “NO ”, “FRONT ” is set to “LARGE ”.

By setting the distance between the speaker’s position (except the

subwoofer) and the listener’s seating position, the sound delay time is

automatically adjusted so that sound reaches the listener at the same

time.

If the Front speakers are set to “SMALL ”, make this setting.

Change the cut-off if the bass from the front speakers is unsatisfactory so

that this bass is output through the subwoofer.

This is displayed when you set “BI-WIRE ” in “Bi-wiring settings”. Select

this when you connect bi-wire compatible front speakers.

You can adjust HF (high frequency) and LF (low frequency) output

balance from the bi-wired speakers. You can also adjust the sound delay

time to offset the difference in HF and LF output directions.

Basic operations with the MULTI CONTROL

Turn to change.

Press to enter.

n To return to the previous setting/To cancel

Press.

n To select another settings

Press several times to return to step 2 in the

operations across and select another setting.

n To finish settings

Press several times to select “EXIT ” and

press [ENTER].

Enter the MULTI CONTROL.

Select “SETUP 2 ”

(“ADVANCE SETUP ”

scrolls once)

and press [ENTER].

Select the settings to change. (ábelow, right)

Speaker settings

Select “SPEAKERS ” and press [ENTER].

Select the speaker and press [ENTER].

SUB-WFR, FRONT, CENTER, SURROUND, SUR BACK

Change the setting and press [ENTER].

SUB-WFR: NO, YES FRONT: SMALL, LARGE

CENTER/SURROUND: NONE, SMALL, LARGE

SUR BACK: NONE, 1 SPKR, 2 SPKRS

NONE: For speakers you haven’t connected (center,

surround or surround back).

SMALL: For speakers that cannot adequately reproduce the

bass range. This setting is sufficient for most

speakers if you are using a subwoofer.

LARGE: For speakers that can reproduce a full sound range,

particularly the bass range below 80 Hz.

1 SPKR: If you connect one surround back speaker.

2 SPKRS: If you connect two surround back speakers.

For the subwoofer (SUB-WFR), select “YES ” if you have

connected one, or “NO ” if you have not.

Repeat steps 3 and 4 for each speaker channel.

Select another setting

Finish setting

VOLUMEINPUT SELECTOR

UPDOWN

ENTER

CANCEL

TUNEPRESET

SPEAKERS

POWER

BAND

BI-AMP

DUAL AMP

MULTI

CONTROL

PHONES

VCR 2

VIDEO IN AUDIO INLR

INPUT SELECTOR

ENTER

CANCEL

MULTI

CONTROL

INPUT SELECTOR

ENTER

CANCEL

MULTI

CONTROL

CANCEL

MULTI

CONTROL

INPUT SELECTOR

Distance setting

Select “DISTANCE ” and press [ENTER].

Select the speaker and press

[ENTER].

FRONT,

CENTER,

SURROUND,

SUR BACK

Set the distance and press

[ENTER].

You can select differences at one foot intervals.

Select another setting

Finish setting

Filter setting

Select “FILTER ” and press [ENTER].

Select the bass filter frequency

and press [ENTER].

• This setting is effective for all speakers set to

“SMALL ” in “Speaker settings”.

80, 100, 150,

200 (Hz)

Select another setting

Finish setting

Bi-amp setting

Select “BI-AMP ” and press [ENTER].

Adjusting the balance

Correcting the HF and LF

difference

Select “

BALANCE

”

and

press [ENTER]

Select “HF PHASE ”

and press [ENTER].

Adjust the balance

and press [ENTER].

• The bar shows the

standard balance.

Set the difference and

press [ENTER].

You can select differences at

0.03 feet intervals.

Select another setting

Finish setting

(MIN) (MAX)

L H

0.00 FEET

(MIN) (MAX)

Difference

(Side view of a

speaker in

cross section)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SAXR55 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SAXR55

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info