Bedienungsanleitung Panasonic SC-BT300 (Seite 47 von 60) (Englisch)

602096

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

RQT9508

Troubleshooting guide

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the chart

do not solve the problem, refer to “Customer Services Directory (United States and Puerto Rico)” on page 58 if you reside in the U.S.A.and Puerto

Rico, or refer to “Product information” on page 59 if you reside in Canada. In other areas, consult your dealer.

The following do not indicate a problem with this unit:

≥Regular disc rotating sounds.

≥Image disturbance during search.

To reset this unit Page

Power

Operation

To restore the unit if it freezes

due to one of the safety

devices being activated.

≥Press and hold [POWER Í/I] on the main unit for 3 seconds. (The settings remain

unchanged.)

—

To return all settings other than

some settings to the factory

preset.

≥Select “Yes” in “Restore Default Settings” in the Setup menu.

This returns all values in the Setup menu and the on-screen menu, except for “Remote

Control Code”, “On-screen Language”, “IP Address/DNS Settings”, “Proxy Server Settings”,

“Network Service”, “DVD-Video Ratings” and “BD-Video Ratings” to the default settings.

To return to the factory preset.

(No setting)

≥Reset the unit as follows:

1 Press [POWER Í/I] on the unit to turn off the unit.

2 Press and hold [5/9] and press [POWER Í/I] and [< OPEN/CLOSE] on the unit at

the same time for more than 5 seconds until “PLEASE WAIT” is displayed on the unit.

3 The power is turned on and then turned off automatically.

—

No power. ≥Insert the AC power supply cord securely into a household AC outlet. 14

The unit switches to standby

mode.

≥This is a power saving feature. It can be changed if desired using “Off Timer” in the Setup

menu.

≥When the time set for the sleep timer has passed, the power will be turned off.

≥One of the unit’s safety devices is activated. Press [POWER Í/I] on the main unit to turn the

unit on.

—

Power of this unit is turned off

when the input for the TV is

changed.

≥If connected with an HDAVI Control 4 compatible TV (VIERA) with the “Auto power stand-by”

setting activated on the TV, when switching the TV input, the unit will be automatically turned

to standby if the TV audio is not output from the unit’s speakers. For details please read the

operating instructions of the TV.

The remote control doesn’t

work properly.

≥The remote control and main unit are using different codes.

Change the code on the remote control.

Press and hold [OK] and the indicated number button at the

same time for more than 5 seconds.

≥The batteries are depleted. Replace them with new ones.

≥It may be necessary to set the code of the remote control again after changing the batteries

for remote control.

≥You are not pointing the remote control at the main unit’s remote control signal sensor during

operation.

≥Colored glass may obstruct the signal reception/transmission.

≥Don’t place the signal sensor in direct sunlight or in areas that may be subject to sunlight

exposure.

—

The unit is on but cannot be

operated.

≥Confirm the correct drive is selected.

≥Some operations may be prohibited by the disc.

≥The unit is hot (“U59” appears on the display). Wait for “U59” to disappear.

≥One of the unit’s safety devices may have been activated.

Reset the unit as follows:

1 Press [POWER Í/I] on the main unit to switch the unit to standby.

If the unit doesn’t switch to standby, press and hold [POWER Í/I] on the main unit for

about 3 seconds. The unit is forcibly switched to standby.

Alternatively, disconnect the AC power supply cord, wait one minute, then reconnect it.

2 Press [POWER Í/I] on the main unit to switch it on. If the unit still cannot be operated,

consult the dealer.

≥Condensation has formed. Wait 1 to 2 hours for it to evaporate.

—

Play fails to start even when

[1PLAY] is pressed.

Play starts but then stops

immediately.

≥Insert the media correctly with the label facing up.

≥The media is dirty.

≥You tried to play a blank media or unplayable media on this unit.

≥The producers of the disc can control how discs are played. So you may not always be able

to control play as described in these operating instructions. Read the disc’s instructions

carefully.

42, 43

—

Cannot eject disc. ≥The unit may have a problem. While the unit is off, press and hold [5/9] and [< OPEN/

CLOSE] on the main unit at the same time for about 5 seconds. Remove the disc and consult

the dealer.

—

Startup is slow.

It takes time before play starts.

≥Startup takes time in the following situations.

– Immediately after a power failure or the AC power supply cord is connected.

–When the unit is connected with an HDMI cable.

—

Played back image is distorted

or does not playback correctly.

([AVCHD])

≥High definition video (transfer rate of 18 Mbps or faster) cannot be played back correctly if it

was recorded on a DVD compatible to double speed or slower.

—

Cannot set “On” in “24p

Output”.

≥Only when the unit is connected to the HDMI terminal of a TV supporting 24p you can select

“On”.

Reference

BT300.book 47 ページ２００９年６月１２日　金曜日　午後１２時１３分

Panasonic SC-BT300 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info