Bedienungsanleitung Panasonic SC-BT300 (Seite 48 von 60) (Englisch)

602096

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

RQT9508

Troubleshooting guide

Displays Page

TV screen and video

The display is dim. ≥Change “FL Display” in the Setup menu. 38

The elapsed time displayed is

actually less than the play time.

≥The displayed play time is converted from the number of frames at 29.97 frames (equal to

0.999 seconds) to one second. There will be a slight difference between the time displayed

and the actual elapsed time (e.g., actual one-hour elapsed time may display as approximately

59 minutes 56 seconds).

—

The images from this unit do

not appear on the TV.

Picture is distorted.

Jittering occurs.

≥Make sure that the TV is connected to the VIDEO OUT terminal, COMPONENT VIDEO OUT

terminals or HDMI AV OUT terminal on this unit.

≥Make sure that the TV’s input setting (e.g., VIDEO 1) is correct.

≥An incorrect resolution is selected in “Component Video Resolution”, when the TV is

connected to COMPONENT VIDEO OUT terminals. While stopped, press and hold [1PLAY]

and [∫STOP] on the main unit at the same time for more than 5 seconds to cancel this

setting. Set the item again.

≥To output video from a device connected with an HDMI cable, set “HDMI Video Mode” to “On”

in the Setup menu.

≥If “24p Output” is set to “On” when the unit is connected to a TV through any terminal other

than HDMI, images may not display properly. In this case, set “24p Output” to “Off”.

≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p images switch

to other images, and a black screen is displayed.

≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video. In this case,

turn “24p Output” to “Off”.

≥An incorrect resolution is selected in “HDMI Resolution”, when the TV is connected to HDMI

AV OUT terminals. While stopped, press and hold [1PLAY] and [∫STOP] on the main unit at

the same time for more than 5 seconds to cancel this setting. Set the item again. However,

Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio are not output in bitstream. To output

the bitstream, select “Restore Default Settings” to restore the factory presets and make

proper settings.

≥Picture may not be seen when more than 2 devices are connected with HDMI cables.

Reduce the number of connected devices.

≥Mobile telephone chargers can cause some disturbance.

≥If you are using an indoor TV antenna, change to an outdoor antenna.

≥The TV antenna wire is too close to the unit. Move it away from the unit.

10, 11

—

The screen changes

automatically.

≥When the “Screen Saver Function” in the Setup menu is set to “On”, the display may return to

the screen saver mode automatically if there is no operation for 5 minutes or more.

Video is not output.

≥An image is not output from the COMPONENT VIDEO OUT terminal or the VIDEO OUT

terminal when the “High Clarity Sound” is enabled. Set the “High Clarity Sound” in the

on-screen menu to “Off” to use the COMPONENT VIDEO OUT terminal or the VIDEO OUT

terminal.

Video is not output in high

definition.

≥High definition video cannot be output through the VIDEO OUT terminal.

≥Confirm that the “HDMI Video Mode”, “HDMI Resolution”, and “Component Video

Resolution” in the Setup menu are set properly.

—

The Setup menu cannot be

accessed.

≥Select “BD/DVD” or “SD” as the source.

—

Status messages do not

appear.

≥Select “Automatic” in “Status Messages” in the Setup menu.

The 4:3 aspect ratio picture

expands left and right.

Screen size is wrong.

≥Use the TV to change the aspect. Refer to your TV’s operating instructions.

≥When using a component video cable, set “Progressive” to “Video”. If the situation is not

restored after that, set “TV Aspect” to “4:3”.

≥When using an HDMI cable, set “TV Aspect” to “16:9”.

—

36, 39

When playing DVD-Video using

progressive output, one part of

the picture momentarily

appears to be doubled up.

≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.

1 Connect this unit to the TV with any cable except the HDMI cable.

2 When you connect with the Component Video cable, set “HDMI Video Mode” to “Off” and

“Component Video Resolution” to “480i” in the Setup menu.

There is no apparent change in

picture quality when adjusted

with the “Video” menu in the

on-screen menu.

≥The effect is less perceivable with some types of video.

—

The masked-off area is masked

in gray.

≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off area is

displayed in black.

Still pictures (JPEG) do not

playback normally.

≥The images that were edited on the PC, such as Progressive JPEG, etc., may not playback.

Reference

BT300.book 48 ページ２００９年６月１２日　金曜日　午後１２時１３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-BT300 Seite 48

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info