Bedienungsanleitung Panasonic SC-PMX152 (Seite 8 von 36) (Englisch)

696402

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

TQBJ0992

1 Turn this system on.

2 Press [RADIO, EXT-IN] on the remote control

repeatedly to select “NETWORK”.

3 To enter “WPS Push” mode

1 Press [SETUP] on the remote control repeatedly

to select “Net Setup” and then press [OK].

“WPS Push” is indicated on the display.

2 Press [OK].

3Press [2, 1] on the remote control to select

“OK? Yes” and then press [OK].

• Alternatively, while pressing and holding down

[5/9] on the main unit, press and hold

[SELECTOR, -NET PRESET] on the main unit for at

least 4 seconds.

• If the unit is already connected to a wireless LAN network,

“Network Initializing” is displayed for about 1 minute.

“WPS” flashes on the display.

4 Activate the WPS button on the wireless router.

• On the main unit’s display, “Success” appears when the

connection is established. (“ ” will be displayed.)

– “Fail” may be displayed if the connection was not made

within the set time limit. Press [OK]. Try the setting

again. If “Fail” is still displayed, try other methods.

∫ Using the WPS PIN code

1 Turn this system on.

2 Press [RADIO, EXT-IN] on the remote control

repeatedly to select “NETWORK”.

3 To enter “WPS PIN” mode

1 Press [SETUP] on the remote control repeatedly

to select “Net Setup” and then press [OK].

2Press [2, 1] on the remote control to select

“WPS PIN” and then press [OK].

• Alternatively, while pressing and holding down

[:/6] on the main unit, press and hold

[SELECTOR, -NET PRESET] on the main unit for at

least 4 seconds.

• If the unit is already connected to a wireless LAN network,

“Network Initializing” is displayed for about 1 minute.

The PIN code is indicated on the display.

4 Enter the PIN code into the wireless router.

Note:

• Once the system enters WPS PIN code mode, you cannot

set up using the WPS button. To use the WPS button, turn

the system off and then on, and redo the network settings.

• Depending on a router, other connected devices may

temporarily lose their connection.

• For details, refer to the operating instructions of the

wireless router.

1 Disconnect the AC mains lead.

2 Connect the main unit to a broadband router, etc.

using a LAN cable.

3 Connect the AC mains lead to the main unit and

turn this system on.

• When the connection is established, “ ” is indicated

on the main unit’s display.

Note:

• Use category 5 or above straight LAN cables (STP) when

connecting to peripheral devices.

• The LAN cable must be connected or disconnected while

the AC mains lead is disconnected.

• Inserting any cable other than a LAN cable in the LAN port

can damage the system.

• If the LAN cable is disconnected, the network-related

settings ( below) will be initialized. In that case, make the

settings again.

• When a LAN cable is connected, the Wi-Fi function will be

disabled.

You can change this system’s name on the network,

change the security options for this system, and use

specific IP address, subnet mask, default gateway,

primary DNS, etc.

Preparation

• Complete the network settings. ( 6)

• Connect your device to the same network as this

system.

• Check this system’s IP address ( 18), and note it

down.

1 Start an Internet browser on your device and

then type this system’s IP address into the

address field to display the settings page.

• It may take a few minutes until the settings page is

displayed depending on the environment. In that case,

reload the browser.

• If the unit is connected with Wi-Fi, only a device name

and the security options for this system can be

changed. Close the settings page after making the

changes.

– To change the device name, select “Change”, and

type a new device name, and then select “Apply”.

– To change the security options for this system, select

“Change” for the AirPlay password setting.

If you have set an AirPlay password previously, you

will need your old password before making changes.

Make the changes and then select “Apply”.

2 Type a device name and then select “Next”.

• Refer to the step 6 of “Using an Internet browser” ( 7)

for details on a device name.

3 Select your security options for this system.

• Refer to the step 7 of “Using an Internet browser” ( 7)

for details on security options for this system.

Method 4:

Using WPS (Wi-Fi Protected Setup™)

A compatible wireless router may have the WPS

identifier mark.

e.g.,

Wired LAN connection

Method 5:

Using a LAN cable

LAN cable

(not supplied)

Broadband router, etc.

e.g.,

To make network-related settings

You can also change the name of this system by

changing a setting in the app “Panasonic Music

Streaming” ( 9). For details on the app, refer to the

site below.

http://panasonic.jp/support/global/cs/audio/app/

(This site is in English only.)

SC-PMX152-150B_EGEBGN-TQBJ0992.book 8 ページ２０１７年３月１６日　木曜日　午後６時１２分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SC-PMX152 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-PMX152

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info