Bedienungsanleitung Panasonic SC-PMX90 (Seite 12 von 16) (Englisch)

734669

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

TQBM0358

Others

As a factory default, this unit will turn to standby mode

automatically if there is no sound and it is not being used

for approximately 20 minutes.

To cancel this function

1 Press [SETUP] repeatedly to select “AUTO OFF”.

2 Press [2, 1] to select “OFF” and then press

[OK].

Note:

• To turn the function on, select “ON” in step 2.

• This setting cannot be selected when radio is the source.

• When connected to a Bluetooth

device, the function does

not work.

Occasionally, Panasonic may release updated software

for this unit that may add or improve the way a feature

operates. These updates are available free of charge.

For more details, refer to the following website.

http://panasonic.jp/support/global/cs/

(This site is in English only.)

Press [SETUP] repeatedly to select “SW VER.” and

then press [OK].

The version of the installed software is displayed.

• Press [OK] to exit.

Troubleshooting

Before requesting service, make the following checks. If

you are in doubt about some of the check points, or if the

solutions indicated do not solve the problem, consult

your dealer for instructions.

Cannot turn on the unit.

• After connecting the AC mains lead, wait about

10 seconds before turning on the unit.

No operations can be done with the remote control.

• Examine that the battery is installed correctly.

Sound is distorted or no sound.

• Adjust the volume of the system.

• Switch off the system, determine and correct the cause,

then switch the system on again. It can be caused by

straining of the speakers through excessive volume or

power, and when using the system in a hot environment.

• Ensure the speaker cables are connected correctly

and securely. (> 4)

• The digital audio input terminal of this unit can only

detect linear PCM (LPCM) signals. For details, refer to

the operating instructions of the device.

A “humming” sound can be heard during playback.

• An AC mains lead or fluorescent light is near the

cables. Keep other appliances and cords away from

the cables of this system.

The unit does not work.

• One of the unit’s safety devices may have been activated.

1 Press [Í/I] on the unit to switch the unit to standby.

• If the unit does not turn off, disconnect the AC mains

lead from the AC outlet, reconnect it to the outlet after

about 30 seconds. Then wait for about 10 seconds.

2 Press [Í/I] on the unit to switch it on. If the unit still

cannot be operated, consult the dealer.

Noise is heard.

• During “AUX” mode, when a device is connected to

both the AUX IN terminals and the USB port, noise

may be generated depending on the device. In this

case, remove the USB cable from the USB port.

Display not shown correctly.

Playback does not start.

• You have not put in the disc correctly. Put it in correctly.

• Disc is dirty. Clean the disc.

• Replace the disc if it is scratched, warped, or non-standard.

•

There is condensation. Let the system dry for 1 to 2 hours.

Reception is poor or a beat sound is heard.

• Keep the antenna away from computers, TVs, other

cables and cords.

• Use an outdoor antenna.

• Switch off the TV or move it away from the system.

If noise is excessive during FM reception.

• Change the audio to be output as monaural.

1 Press [RADIO MENU] repeatedly to select “FM MODE”.

2 Press [2, 1] to select “MONO” and then press [OK].

The sound becomes monaural.

• To cancel, select “STEREO” or change the frequency.

In normal circumstances, select “STEREO”.

The USB device or the contents in it cannot be read.

• The format of the USB device or the contents in it is/

are not compatible with the system.

Slow operation of the USB device.

• Large content size or large memory USB device takes

longer time to read.

The elapsed time shown is different from the actual

play time.

• Transfer the data to another USB device or backup the

data and reformat the USB device.

Pairing cannot be done.

• Check the Bluetooth

device condition.

The device cannot be connected.

• The pairing of the device was unsuccessful or the

registration has been replaced. Try pairing the device

again.

• This system might be connected to a different device.

Disconnect the other device and try pairing the device

again.

• If “MODE 2” is selected in “LINK MODE”, select

“MODE 1”. (> 6)

• If the problem persists, turn the unit off and on, then try

again.

The device is connected but audio cannot be heard

through this system.

• For some built-in Bluetooth

devices, you have to set

the audio output to “SC-PMX92” or “SC-PMX90”

manually. Read the operating instructions for the

device for details.

The sound is interrupted.

• The device is out of the 10 m communication range.

Bring the Bluetooth

device closer to this system.

• Remove any obstacle between this system and the

device.

• Other devices that use the 2.4 GHz frequency band

(wireless router, microwaves, cordless phones, etc.)

are interfering. Bring the Bluetooth

device closer to

this system and distance it from the other devices.

• Select “MODE 1” for stable communication. (> 6)

Auto off function

Software update

Checking the software version

Common problems

Disc

Radio

USB

Bluetooth

SC-PMX90-92-EGEBGN~TQBM0358.book 12 ページ２０１９年１月１６日　水曜日　午後２時５５分

Panasonic SC-PMX90 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SC-PMX90

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info