734669

Panasonic SC-PMX90 Seite 13

13
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
13
TQBM0358
“AUX-IN auto play” does not work.
• You have not connected the external music device
correctly.
• Increase the volume of the external music device.
• If “OFF” was selected during “AUX-IN AUTO PLAY”,
select “ON”.
Unintentional automatic switch to AUX source.
• Connect the audio cable to the system only after all the
other connections have been made.
Noise may be detected when connecting the external
music device and it will cause the set to automatically
switch to AUX source.
The PC does not recognise this system.
• Check your operating environment. (> 11)
• Restart the PC, turn off and on this system, and then
reconnect the USB cable.
• Use another USB port of the connected PC.
• Install the dedicated driver if using a PC with Windows.
“--:--”
• You connected the AC mains lead for the first time or
there was a power failure recently. Set the clock.
“ADJUST CLOCK”
• Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
• Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
• The unit has been left unused for about 20 minutes
and will shut down in a minute. Press any button to
cancel it.
“CHECKING CONNECTION”
• The unit is checking the connected USB device.
“ERROR”
• An incorrect operation was done. Read the instructions
and try again.
“F” / “F” (“ ” stands for a number.)
• There is a problem with this unit.
Disconnect the AC mains lead from the AC outlet, reconnect
it to the outlet after about 30 seconds. Wait for about 10
seconds, then turn on the unit. If the problem still persists,
disconnect the AC mains lead and consult your dealer.
“NO DEVICE”
• The USB device is not connected. Examine the
connection.
“NO DISC”
• You have not put in a disc or put in a disc that the
system cannot play.
“NO PLAY”
• Examine the content. You can only play supported
format. (> 14)
• The files in the USB device can be corrupted. Format
the USB device and try again.
• The unit may have a problem. Turn the unit off and
then on again.
“NO PRESET” ([PMX92])
• There are no preset DAB/DAB+ stations to select.
Preset some channels.
“NO SIGNAL” ([PMX92])
• This station cannot be received. Check your antenna.
“DEVICE NO RESPONSE”
“HUB NOT SUPPORTED”
“NOT SUPPORTED”
• You have connected an unsupported USB device.
“OPT UNLOCKED”
• “OPT” is selected, but no device is connected.
• The sampling frequency components, etc. of the audio
signals are not input correctly.
– For supported formats, refer to “Connecting to OPT IN
(Optical Audio In) terminal” (@ 4).
“PC UNLOCKED”
• “PC” is selected, but a PC is not connected.
“PGM FULL”
• The number of programmed tracks is more than 24.
“PLAYERROR”
• You played an unsupported file. The system will skip
that track and play the next one.
“READING”
• The unit is checking the CD information. After this
display has disappeared, start operating.
• When starting playback of DSD files, it may take time
to read the file. Wait until reading completes.
“REMOTE ” (“ ” stands for a number.)
• The remote control and this unit are using different
codes. Change the code on the remote control.
– When “REMOTE 1” is displayed, press and hold [OK]
and [1] for at least 4 seconds.
– When “REMOTE 2” is displayed, press and hold [OK]
and [2] for at least 4 seconds.
“SCAN FAILED” ([PMX92])
• Stations are not receivable. Check your antenna and try
DAB/DAB+ manual tuning.
“USB OVER CURRENT ERROR”
• The USB device is drawing too much power. Remove
the USB device. Switch the system off and on again.
“VBR”
• The system cannot show the remaining play time for
variable bit rate (VBR) tracks.
“WAIT”
• This is displayed, for example, when this unit is turning
off.
Reset the memory when the following situations occur:
• There is no response when buttons are pressed.
• You want to clear and reset the memory contents.
1 Disconnect the AC mains lead.
Wait 30 seconds before you continue with step 2.
2 While you press and hold [Í/I] on the main unit,
connect the AC mains lead again.
Keep holding down [Í/I] until “---------” appears on
the display.
3 Release [Í/I].
All the settings are set back to the factory default.
It is necessary to set the memory items again.
When other Panasonic equipment responds to the
remote control of this system, change the remote control
code for this system.
To set the code to “REMOTE 2”
1
Press [SELECTOR] on the main unit to select “CD”.
2
Press and hold [
∫
] on the main unit and [2] on the
remote control until “REMOTE 2” is shown.
3 Press and hold [OK] and [2] for a minimum of
4 seconds.
• The factory default is “REMOTE 1”.
• To change the mode back to “REMOTE 1”, repeat the
steps above but replace the button pressed on the
remote control from [2] to [1].
AUX
PC
Main unit displays
Memory reset (initialisation)
Remote control code
SC-PMX90-92-EGEBGN~TQBM0358.book 13 ページ ２０１９年１月１６日　水曜日　午後２時５５分
… 13 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic SC-PMX90 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Panasonic SC-PMX90

Panasonic SC-PMX90 Bedienungsanleitung - Deutsch, Holländisch, Französisch, Italienisch - 60 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info