612777
22
Zoom out
Zoom in
Vorherige Seite
1/32
Nächste Seite
22
RQT0A22
The following messages or service numbers may
appear on the unit’s display.
“--:--”
You plugged the AC mains lead in for the first time or there was a
power failure recently. Set the time (l 17).
“ADJUST CLOCK”
Clock is not set. Adjust the clock accordingly.
“ADJUST TIMER”
Play timer is not set. Adjust the play timer accordingly.
“AUTO OFF”
The unit has been left unused for about 20 minutes and will shut
down within a minute. Press any button to cancel it.
“DL ERROR”
The software download has failed. Press any button to exit.
Please try again later.
The server cannot be found. Press any button to exit. Make sure
that the wireless network is connected to the Internet.
“ERROR”
Incorrect operation is performed. Read the instructions and try
again.
“F” / “F” (“ ” stands for a number.)
There is a problem with this unit.
Write down the displayed number, disconnect the AC mains lead
and consult your dealer.
“FAIL”
Updating or setting has failed. Read the instructions and try again.
“ILLEGAL OPEN”
Sliding door is in the wrong position. Turn the unit off and on
again. If this display appears again, consult the dealer.
“LEVEL 0”
There is no link between this system and the wireless router.
Try the following operations:
Check that the wireless router is turned on.
Turn this system off and on again.
Reset the wireless network settings. (l 7)
If the problem persists, consult your dealer.
“LINKING”
This system is trying to connect to the last connected Bluetooth
®
device when “BLUETOOTH” is selected.
This system is communicating with the wireless router to complete
the network settings.
Depending on the wireless router this process may take a few
minutes. Try moving this system closer to the wireless router.
“NETWORK INITIALIZING”
“SETUP IN PROGRESS, TRY AGAIN”
The system is carrying out an internal process.
Wait for approximately 3 minutes.
Do not disconnect the AC mains lead. Doing so may cause
malfunction.
“NO CONNECT”
This system cannot connect to the network.
Check the network connection. (l 7)
“NODEVICE”
The USB device is not inserted correctly. Read the instructions
and try again (l 6).
“NO DISC”
Insert the disc to be played (l 6).
“NO MEMORY”
There are no preset DAB+ stations to select. Preset some
channels. (l 14)
“NO PLAY
A CD that is not in CD-DA or MP3 format is inserted. It cannot be
played.
Examine the content. You can only play supported format. (l 24)
The files in the USB device can be corrupted. Format the USB
device and try again.
The unit may have a problem. Turn the unit off and then on again.
“NO SIGNAL”
This station cannot be received. Check your antenna (l 5).
“PLAYERROR”
You played an unsupported MP3 file. The system will skip that
track and play the next one.
“READING”
The unit is checking the CD/USB information. After this display
has disappeared, start operating.
“REMOTE ” (“ ” stands for a number.)
The remote control and this unit are using different codes. Change
the code on the remote control.
When “REMOTE 1” is displayed, press and hold [OK] and [ ]
for at least 4 seconds.
When “REMOTE 2” is displayed, press and hold [OK] and [CD/USB]
for at least 4 seconds.
“SCAN FAILED”
Stations are not receivable. Check your antenna and try Auto
scanning (l 14).
If “SCAN FAILED” is still displayed find the best signal reception
with the “MANUAL SCAN” tuning function. (l 15)
“USB OVER CURRENT ERROR”
The USB device is drawing too much power. Select a source other
than “USB”, remove the USB and turn the unit off.
“VBR”
The system cannot show the remaining play time for variable bit
rate (VBR) tracks.
“WAIT”
This is displayed, for example, when this unit is turning off.
This is flashing when the system is trying to enter a network
setting mode.
The network indicator “ ” blinks
This may occur when, for instance, the network connection is
interrupted.
Messages
SC-ALL5CD-EGEBGN~RQT0A22.book 22 ページ 2015年4月23日 木曜日 午後4時44分
22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Panasonic SCALL5CDGN wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Panasonic SCALL5CDGN

Panasonic SCALL5CDGN Kurzanleitung - Englisch - 1 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info