Bedienungsanleitung Panasonic SCHT1500 (Seite 46 von 52) (Englisch)

18686

Zoom out

Zoom in

Vorherige Seite

1/52

Nächste Seite

RQT7619

INFO

Error messages

On the television Page

On the unit’s display

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart

do not solve the problem, refer to the “Customer Services Directory” on page 51 if you reside in the U.S.A., or refer to the “Product information” on

Backcover if you reside in Canada.

The following do not indicate a problem with this unit:

Power Page

Cannot finish recording

completely.

≥The program was copy-protected.

≥The HDD or disc may be full.

—

Cannot play. ≥You inserted an incompatible disc (Discs recorded in PAL video etc.). —

Cannot record on the disc. ≥The disc may be dirty or scratched. 10

Please check the disc.

Unable to format.

Cannot record. Disc is full. ≥Create space by erasing any unnecessary titles. [HDD] [RAM]

≥Use a new disc. [RAM] [DVD-R]

22, 27, 35

—

Cannot record. Maximum

number of titles exceeded.

Error has occurred. Please

press ENTER.

≥Press [ENTER] to start recovery process. You cannot operate the unit while it is recovering

(“SELF CHECK” appears on the unit’s display).

—

No disc ≥The disc may be upside down. —

Please change the disc. ≥There may be a problem with the disc. Press [< OPEN/CLOSE] on the main unit to

remove it and check it for scratches or dirt. (The unit turns off automatically after you open

the tray.)

This is a non-recordable disc. ≥The unit cannot record on the disc you inserted. Insert a DVD-RAM or unfinalized DVD-R.

≥You inserted an unformatted DVD-RAM. Format the disc with this unit.

—

This disc is not formatted properly.

≥The operation is prohibited by the unit or disc. —

CHK REMOTE 

(“∑” stands for a number.)

≥The remote control and main unit are using different codes. Change the code on the

remote control.

Press and hold [ENTER] and the indicated number button at

the same time for more than 2 seconds.

HARD ERR ≥If there is no change after turning the unit on and off, consult the dealer where the unit was

purchased.

—

HDD SLP ≥In order to extend HDD life, the HDD is in SLEEP mode. Press [HDD] to activate. 10

NO READ ≥The disc is dirty or badly scratched. The unit cannot record, play, or edit.

≥You have used a DVD-RAM/PD lens cleaner and it has finished. Press [< OPEN/CLOSE]

on the main unit to eject the disc.

—

PLEASE WAIT ≥Displayed when the unit is started. This is not a malfunction. —

SELF CHECK ≥There was a power failure or the AC plug was disconnected while the unit was on. The unit

is carrying out its recovery process. Wait until the message disappears.

—

UNSUPPORT ≥You have inserted a disc the unit cannot play or record on.

≥The signal input into the L1 OPTICAL IN terminal is not Dolby Digital or Linear PCM.

—

U14 ≥The unit is hot.

The unit switches to standby for safety reasons. Wait for about 30 minutes until the

message disappears.

Select a position with good ventilation when installing the unit. Do not block the cooling fan

on the rear of the unit.

—

U99 ≥The unit fails to operate properly. Press [POWER Í/I] on the main unit to switch the unit to

standby. Now press [POWER Í/I] on the main unit again to turn the unit on.

—

AF F61 ≥Check and correct the speaker cord connections.

If this does not fix the problem, there is a power supply problem. Consult the dealer.

Setup

Guide

DIGITAL UNLOCK ≥There is no signal input to the L1 OPTICAL IN terminal.

➡ Make sure to check the connections and if the power of the connected equipment is

turned on.

—

Troubleshooting guide

≥Regular disc rotating sounds. The sound of disc rotating may

become louder especially when finalizing a DVD-R.

≥Poor reception due to atmospheric conditions.

≥Image disturbance during search.

≥Interruptions to reception due to periodic satellite broadcasting

breaks.

≥A sound is heard when the HDD goes into the SLEEP mode, or

operations are slow to respond in SLEEP mode.

No power. ≥Insert the AC power supply cord and system cable securely.

Setup Guide

The unit switches to the

standby mode.

≥This is a power saving feature. Change “Off Timer” in the SETUP menu, if you would prefer.

≥

One of the unit’s safety devices is activated. Press [POWER

/I] on the main unit to turn the unit on.

—

7619en.book 46 ページ２００４年５月６日　木曜日　午前９時３３分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic SCHT1500 Seite 46

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic SCHT1500

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info