Bedienungsanleitung Panasonic UT-MB5000 (Seite 23 von 36) (Englisch)

597888

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Troubleshooting

Troubleshooting (Basic)

Follow the instructions below when a problem has occurred. There is also an advanced troubleshooting guide in the

“Reference Manual”. For a software problem, refer to the software’s instruction manual. If the problem persists, contact

Panasonic Technical Support. You can also check the computer’s status in the PC Information Viewer

(

Reference Manual “Troubleshooting (Advanced)”).



Starting Up

Cannot start up.

The power indicator or battery

indicator is not lit.

Connect the AC adaptor.

Remove the AC adaptor, and then connect it again.

If a device is connected to the USB port, disconnect the device, or set [USB Port]

or [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.

Check the [UEFI Boot] setting of the Setup Utility. [UEFI Boot] should be set to [Enabled].

You have forgotten the pass-

word.

Supervisor Password or User Password: Contact Panasonic Technical Support.

Administrator password:



If you have a password reset disk, you can reset the administrator password. Set

the disk and enter any wrong password, then follow the on-screen instructions

and set a new password.



If you do not have a password reset disk, install (

page 19) and set up Win-

dows, and then set a new password.

“Remove disks or other me-

dia. Press any key to restart”

or a similar message ap-

pears.

A oppy disk is in the drive and it does not contain system startup information. Re-

move the oppy disk and press any key.

If a device is connected to the USB port, disconnect the device, or set [USB Port]

or [Legacy USB Support] to [Disabled] in the [Advanced] menu of the Setup Utility.

If the problem persists after removing the disk, it may be a ash memory failure.

Contact Panasonic Technical Support.

Windows startup and opera-

tion is slow.

Start the Setup Utility (

Reference Manual “Setup Utility”) to return the Setup

Utility settings (excluding the passwords) to the default values. Start the Setup Util-

ity and make the settings again. (Note that the processing speed depends on the

application software, so this procedure may not make Windows faster.)

If you installed a resident software after purchase, turn off the residence.

The date and time are incor-

rect.

Make the correct settings.

Open the Control Panel.

Touch [Clock, Language, and Region] - [Date and Time].

Touch [Change time zone…].

Select the time zone, then touch [OK].

Touch [Change date and time…], then set the date and time.

If the problem persists, the internal clock battery may need to be replaced. Contact

Panasonic Technical Support.

When the computer is connected to LAN, check the date and time of the server.

The 2100 A.D. or later year will not be correctly recognized on this computer.

[Executing Battery Recalibra-

tion] screen appears.

The Battery Recalibration was canceled before Windows was shut down last time.

To start up Windows, turn off the computer by the power switch, and then turn on.

[Enter Password] does not

appear when resuming from

sleep/hibernation.

Select [Enabled] in [Password On Resume] in the [Security] menu of the Setup

Utility (

Reference Manual “Setup Utility”).

The Windows password can be used instead of the password set in the Setup Utility.

Add a password.

1. Display “Charm” and touch

- [Change PC settings] - [Accounts].

2. Touch [Sign-in options], and touch [Add] under “Password”.

Open the Control Panel, touch [System and Security] - [Power Options] - [Re-

quire a password on wakeup] and add a check mark for [Require a password].

Cannot resume.

One of the following operations may have been carried out. Press the power switch

to turn on the computer. Data not saved will be lost.



In sleep mode, the AC adaptor was disconnected, or a peripheral was connected

or disconnected.



The power switch was pressed for four seconds or longer to forcibly turn off the computer.

An error may occur when the computer automatically enters the sleep or hibernation

mode while the screensaver is active. In this case, turn off the screensaver or change

the pattern of the screensaver.

DFQW5829ZA_UT-MB_8_OI_M.indb 23 2013/11/13 13:23:25

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic UT-MB5000 Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info