Bedienungsanleitung Panasonic WV-SC384 (Seite 170 von 244) (Englisch)

550986

170

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

UPnP

This camera support UPnP (Universal Plug and Play). By using the UPnP function, it becomes possible to

configure the following automatically.

• Configuration of the port forwarding function of the router (However, a router supporting UPnP is required.)

This configuration is useful when accessing the camera via the Internet or from a cellular phone/mobile

terminal.

• Automatic refreshment of the shortcut to the camera that is created on the [My Network Places] folder

([Network] folder when using Windows Vista or Windows 7) of the PC even when the IP address of the

camera changes.

[Auto port forwarding]

Select “On” or “Off” to determine whether or not to use the port forwarding function of the router.

To use the port forwarding function, the router in use must support UPnP and the UPnP must be enabled.

• Default: Off

Note

• Due to port forwarding, the port number may sometimes be changed. When the number is changed,

it is necessary to change the port numbers registered in the PC and recorders, etc.

• The UPnP function is available when the camera is connected to the IPv4 network. IPv6 is not

supported.

• To check if auto port forwarding is properly configured, click the [Status] tab on the “Maintenance” page,

and check that the “Enable” is displayed for “Status” of “UPnP”. (®page 218)

When “Enable” is not displayed, refer to “Cannot access the camera via the Internet.” in the

“23 Troubleshooting” section. (®page 231)

[Camera short cut]

Select whether or not to create the shortcut to the camera on the [My Network Places] folder ([Network] folder

when using Windows Vista or Windows 7) of the PC. When creating the shortcut, select “On”.

To use the shortcut function to the camera, enable the UPnP function on the PC in advance.

• Default: Off

Note

• To display the shortcut to the camera on the [My Network Places] folder ([Network] folder when using

Windows Vista or Windows 7) of the PC, it is necessary to add the Windows component. Refer to the

following to enable the UPnP function.

For Windows XP

[Start] ® [Settings] ® [Control Panel] ® [Add or Remove Programs] ® [Add/Remove Windows

Components] ® select [Networking Services] ® [Details] ® check [Internet Gateway Device Discovery

and Control Client] and [UPnP User Interface] ® [OK] ® [Next] ® Complete

For Windows Vista

[Start] ® [Control Panel] ® [Network and Internet] ® [Network and Sharing Center] ® expand the

section of [Network discovery] of [Sharing and Discovery] ® select [Turn on network discovery] ® click

[Apply] ® Complete

For Windows 7

[Start] ® [Control Panel] ® [Network and Internet] ® [Network and Sharing Center] ® select [Turn on

network discovery] of [Network discovery] of [Change advanced sharing settings] ® click [Save

changes] ® Complete

HTTPS

It is possible to enhance the network security by encrypting the access to cameras using the HTTPS function.

Refer to page 174 for how to configure the HTTPS settings.

170 Operating Instructions

17 Configuring the network settings [Network]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic WV-SC384 Seite 170

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic WV-SC384

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info