Bedienungsanleitung Panasonic WV-SC384 (Seite 209 von 244) (Englisch)

550986

209

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

2. Configure [Wi-Fi Protected Setup (WPS)].

– Select “Allow” for “External registration”. (Default: Allow)

– Select “Use” for “WPS compliant (PIN method)”. (Default: Not use)

– Click the [Generate] button or [Default] button to set the “PIN code”.

• Available number of characters: 8 characters

• Available characters: Numbers

• Default: None (blank)

Note

• The [Generate] button of “PIN code” generates a random 8 digit PIN code.

• The [Default] button of “PIN code” sets a preset 8 digit PIN code.

• When “Use” is selected for “WPS compliant (PIN method)”, settings cannot be performed

automatically using the WIRELESS button during start up for the PIN method.

3. Click the [Set] button.

→ A message asking you if you want to restart the camera is displayed. Click [OK]. Wait about 2 minutes

until the camera restarts.

4. Disconnect the LAN cable from the camera and reconnect the camera to the power outlet.

→ The camera will start about 90 seconds after connecting the power.

• After the camera is started, the WPS settings are only active for about 2 minutes. Therefore, perform

the settings in step 5 and restart the wireless router as quickly as possible (within 2 minutes).

5. Enter the camera's 8 digit PIN code into the wireless router, and restart the wireless router with the WPS

PIN code method.

• For more information, refer to the operating instructions included with your wireless router.

→ Settings between the wireless router and the camera will automatically start.

→ The WIRELESS button stops blinking orange and lights green. When the live indicator lights green,

the wireless settings have been successfully completed.

6. After the WIRELESS button lights green, start the “IP Setting Software” on the PC and access the camera.

• See page 222 for information on accessing the camera with the “IP Setting Software”.

• Confirm the status of the wireless connection on the [Status] tab of the “Wireless” page.

(®page 210)

Note

• If about 2 minutes pass after the WIRELESS button starts blinking and the wireless connection is not

completed, the WIRELESS button will blink red for about 10 seconds and then go off. If this happens

the wireless settings have failed. Check the wireless router's settings and connection procedures, and

then try performing the settings again.

• If the WPS settings fail to automatically configure, check the settings of the wireless router and the

camera.

• If you want to turn off the WIRELESS button’s and live indicator's green light, change the “Indicator”

settings on the [Basic] tab of the “Basic” page. (®page 55)

• When the WPS settings have successfully been automatically configured, “External registration” is

changed to “Not allow” from “Allow”.

Operating Instructions 209

18 Use the camera on a wireless LAN [Wireless] (SW174W only)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic WV-SC384 Seite 209

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic WV-SC384

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info