Bedienungsanleitung Panasonic WV-SC384 (Seite 207 von 244) (Englisch)

550986

207

Zoom out

Zoom in

Vorherige Seite

1/244

Nächste Seite

Performing settings automatically with the WIRELESS button (WPS

indicator)

Use the camera's WIRELESS button to automatically perform wireless settings.

1. Turn on the camera without connecting the LAN cable to enable the wireless settings.

→ After the initial pan/tilt operations are performed, the live indicator stops blinking orange and lights

orange. The live indicator lights orange and the camera starts up in wireless LAN mode about 90

seconds after the camera was turned on.

2. Select ON for the WPS function (Push-button method (PBC)) on the wireless router. (For more information,

refer to the operating instructions included with your wireless router.)

3. Press and hold down the WIRELESS button for a second or more until it blinks orange.

→ The camera and the wireless router automatically start performing wireless settings. Settings may take

up to 2 minutes to be performed.

→ When the automatic wireless settings have been successfully completed, the camera restarts about 5

seconds after the WIRELESS button stops blinking orange and lights green. The WIRELESS button

goes off, and after about 90 seconds lights green again when the wireless connection has been

successfully completed.

→ The wireless settings are updated.

4. After the WIRELESS button lights green, start the “IP Setting Software” on the PC and access the camera.

• See page 222 for information on accessing the camera with the “IP Setting Software”.

• Confirm the status of the wireless connection on the [Status] tab of the “Wireless” page.

(®page 210)

Note

• If about 2 minutes pass after the WIRELESS button starts blinking and the wireless connection is not

completed, the WIRELESS button will blink red for about 10 seconds and then go off. If this happens

the wireless settings have failed. Check the wireless router's settings and connection procedures, and

then try performing the settings again.

• If the WPS settings fail to automatically configure, check the settings of the wireless router and the

camera.

• If you want to turn off the WIRELESS button’s and live indicator's green light, change the “Indicator”

settings on the [Basic] tab of the “Basic” page. (®page 55)

• When the WPS settings have successfully been automatically configured, “External registration” is

changed to “Not allow” from “Allow”.

Performing settings automatically with PIN code settings

There are 2 methods for performing settings automatically with PIN code settings: using the PIN code preset

to the wireless router or using a selected PIN code set to the camera.

Using the PIN code configured to the wireless router

1. Check the preset 8 digit PIN code of the wireless router with a PC.

• For more information on how to check the preset PIN code of the wireless router, refer to the operating

instructions included with your wireless router.

• Depending on the wireless router used, the PIN code (default setting) may be written on a sticker

attached to the wireless router.

2. Connect the PC to the camera with a wired LAN connection and click the [Basic] tab on the “Wireless”

page.

Operating Instructions 207

18 Use the camera on a wireless LAN [Wireless] (SW174W only)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Panasonic WV-SC384 Seite 207

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Panasonic WV-SC384

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info