458602
49
Zoom out
Zoom in
Vorherige Seite
1/175
Nächste Seite
4 Operation
4-8 FrameSaver NP 110 Users Manual - Installation Guide 980-001-0240B
November
2000
Device
Configuration
The Device Configuration screen allows you to view and alter parameters for System
and Modem operations.
The Device Configuration screen is shown in Figure 4-3.
Fi
g
ure 4-3 Device Confi
g
uration Screen
All FrameSaver NP 110 screen entries and selections are made by entering the two or
three characters shown in brackets next to the field titles, equals =, then entering the
value or string followed by ENTER.
Example: To enter ABC in the Name field,
Type: N=ABC and press ENTER
Current selections are highlighted by bracketing with >>.....<< characters.
Device Configuration
1. Enter Name and Location of this FrameSaver NP 110 installation (optional but
recommended).
2. Enter Contact Name and Phone Number of local technical contact (optional).
3. Enter WAN IP Address for SNMP management of the FrameSaver NP 110. If set
to the default value as shown in Figure 4-3, the IP Address will be learned
automatically. The first valid IP Address will be learned. Once a value is entered
or learned automatically, it will replace the 0.0.0.0 value and auto learning will
be discontinued.
4. Enter Payload or CPE (private user) IP Address for PVC management of the
FrameSaver NP 110.
***************************** Device Configuration *****************************
Frm Mgr [Z=]
Name [N=]: F@43802 >>1) FrRelay<<
Location [L=]: Fair Lawn, N.J. 2) ClrChan
Contact [C=]: J. Jones
WAN IP Add [I=]: 0.0.0.0 Payload/CPE IP Add [J=]: 0.0.0.0
------ Modem Setup / Model: RC288DPi Rev 05BA V1.400-V34_DS ------
Dial String [D=]:
Answer Call [AC=]:
Aux1 Setup [A1=]: A96N8AT&K0Q1^MATA
Aux2 Setup [A2=]: A96N8AT&K0Q1^MATA
(NOTE: Text & IP entries may not be made in combination with other parameters!)
ModemLine [M=] RtryCount[R=#]:2 RtryHoldoff[H=#]:30 InactivityLogout[O=#]:15
1) Test 1 thru 4 1 thru 60 seconds 1 thru 30 minutes
>>2) No Test<<
WAN Encap [T=] MTUSize[W=#]:1492 View Pswrd [P=]:11111111
P/C Encap [U=] >>1) Learning<< 88 thru 4000 Octs Test Pswrd [E=]:22222222
>>1) Raw<< 2) Raw Config Pswrd [F=]:33333333
2) IETF 3) IETF ---- CHAP Name/Key --- Super Pswrd [S=]:********
4) SNAP [CN=]:CHAPNAME******** Super Verify [V=]:********
Help[?] Save[SA] Cancel[X] [CK=]:**************** System Pswrd [Y=]:DISABLED
>
49

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Paradyne FrameSaver NP 110 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info