Bedienungsanleitung Parkside 360564 - IAN 360564 (Seite 9 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch)

763673

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

4GB/IE

• Allen key 6 mm (C)

• Allen key 3 mm (D)

• Operating manual

5. Intended use

The multifunction sliding cross cut mitre saw is designed to

crosscut wood, plastic, aluminium, copper and metal (not ex-

ceeding 15 HRC), respective of the machine’s size. The sliding

cross cut mitre saw is not designed for cutting ﬁrewood.

Warning! Do not use the sliding cross cut mitre saw to cut

materials other than those speciﬁed described in manual.

Warning! The supplied saw blade is intended exclusively for

sawing the following materials:

wood, wood derived products (MDF, chipboard, plywood,

blockboard, hardboard, etc.), wood with nails, plastic, non-

ferrous metals and 3mm mild steel plates.

Note: Wood containing non-galvanised nails or screws can

also be safely cut when carefully handled.

Note: Do not use the saw blade to cut galvanised materi-

als or wood containing galvanised nails. Do not use the saw

blade to saw ﬁrewood!

The equipment is to be used only for its prescribed purpose.

Any other use is deemed to be a case of misuse. The user / op-

erator and not the manufacturer will be liable for any damage

or injuries of any kind caused as a result of this.

The equipment is to be operated only with suitable saw blades.

It is prohibited to use any type of cutting-oﬀ wheel.

To use the equipment properly you must also observe the safety

information, the assembly instructions and the operating instruc-

tions to be found in this manual.

All persons who use and service the equipment have to be

acquainted with this manual and must be informed about the

equipment’s potential hazards. It is also imperative to observe

the accident prevention regulations in force in your area. The

same applies for the general rules of health and safety at work.

The manufacturer will not be liable for any changes made to

the equipment nor for any damage resulting from such chang-

es. Even when the equipment is used as prescribed it is still im-

possible to eliminate certain residual risk factors. The following

hazards may arise in connection with the machine’s construc-

tion and design:

• Contact with the saw blade in the uncovered saw zone.

• Reaching into the running saw blade (cut injuries).

• Kick-back of workpieces and parts of workpieces.

• Saw blade fracturing.

• Catapulting of faulty carbide tips from the saw blade.

• Damage to hearing if ear-muﬀs are not used as necessary.

• Harmful emissions of wood dust when used in closed rooms.

Please note that our equipment has not been designed for use

in commercial, trade or industrial applications. Our warranty

will be voided if the equipment is used in commercial, trade or

industrial businesses or for equivalent purposes.

6. Safety information

General power tool safety warnings

m WARNING! Read all safety warnings, instruc-

tions, illustrations and speciﬁcations provided with

this power tool. Failure to follow all instructions listed below

may result in electric shock, ﬁre and/or serious injury.

Save all warnings and instructions for future refer-

ence.

The term “power tool” in the warnings refers to your mains-operat-

ed (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

a) Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

b) Do not operate power tools in explosive atmos-

pheres, such as in the presence of ﬂammable

liquids, gases or dust. Power tools create sparks

which may ignite the dust or fumes.

c) Keep children and bystanders away while op-

erating a power tool. Distractions can cause you to

lose control.

2. Electrical safety

a) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodiﬁed plugs and matching outlets will reduce

risk of electric shock.

b) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed or grounded.

c) Do not expose power tools to rain or wet condi-

tions. Water entering a power tool will increase the risk

of electric shock.

d) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electric shock.

e) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of a

cord suitable for outdoor use reduces the risk of electric shock.

f) If operating a power tool in a damp location

is unavoidable, use a residual current device

(RCD) protected supply. Use of an RCD reduces the

risk of electric shock.

3. Personal safety

a) Stay alert, watch what you are doing and use

common sense when operating a power tool.

Do not use a power tool while you are tired or

under the inﬂuence of drugs, alcohol or medica-

tion. A moment of inattention while operating power tools

may result in serious personal injury.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside 360564 - IAN 360564 Seite 9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info