Bedienungsanleitung Parkside 360564 - IAN 360564 (Seite 10 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch)

763673

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

5GB/IE

b) Use personal protective equipment. Always

wear eye protection. Protective equipment such as

a dust mask, non-skid safety shoes, hard hat or hearing

protection used for appropriate conditions will reduce per-

sonal injuries.

c) Prevent unintentional starting. Ensure the

switch is in the oﬀ-position before connecting to

power source and/or battery pack, picking up

or carrying the tool. Carrying power tools with your

ﬁnger on the switch or energising power tools that have the

switch on invites accidents.

d) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result in

personal injury.

e) Do not overreach. Keep proper footing and

balance at all times. This enables better control of the

power tool in unexpected situations.

f) Dress properly. Do not wear loose clothing or

jewellery. Keep your hair and clothing away

from moving parts. Loose clothes, jewellery or long

hair can be caught in moving parts.

g) If devices are provided for the connection of

dust extraction and collection facilities, ensure

these are connected and properly used. Use of

dust collection can reduce dust-related hazards.

h) Do not let familiarity gained from frequent use

of tools allow you to become complacent and

ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

4. Power tool use and care

a) Do not force the power tool. Use the correct power

tool for your application. The correct power tool will do the

job better and safer at the rate for which it was designed.

b) Do not use the power tool if the switch does not

turn it on and oﬀ. Any power tool that cannot be con-

trolled with the switch is dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or remove the battery pack, if detachable,

from the power tool before making any adjust-

ments, changing accessories, or storing power

tools. Such preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of chil-

dren and do not allow persons unfamiliar with

the power tool or these instructions to oper-

ate the power tool. Power tools are dangerous in the

hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition that

may aﬀect the power tool’s operation. If dam-

aged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

power tools.

f) Keep cutting tools sharp and clean. Properly main-

tained cutting tools with sharp cutting edges are less likely

to bind and are easier to control.

g) Use the power tool, accessories and tool bits

etc. in accordance with these instructions, tak-

ing into account the working conditions and the

work to be performed. Use of the power tool for

operations diﬀerent from those intended could result in a

hazardous situation.

h) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and con-

trol of the tool in unexpected situations.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replacement

parts. This will ensure that the safety of the power tool is

maintained.

Safety instructions for mitre saws

a) Mitre saws are intended to cut wood or wood-

like products and cold metal when they are set

at diﬀerent running speed. Abrasive dust causes

moving parts such as the lower guard to jam. Sparks from

abrasive cutting will burn the lower guard, the kerf insert

and other plastic parts.

b) Use clamps to support the workpiece when-

ever possible. If supporting the workpiece by

hand, you must always keep your hand at least

100 mm from either side of the saw blade. Do

not use this saw to cut pieces that are too small

to be securely clamped or held by hand. If your

hand is placed too close to the saw blade, there is an in-

creased risk of injury from blade contact.

c) The workpiece must be stationary and clamped

or held against both the fence and the table.

Do not feed the workpiece into the blade or

cut “freehand” in any way. Unrestrained or moving

workpieces could be thrown at high speeds, causing injury.

d) Push the saw through the workpiece. Do not

pull the saw through the workpiece. To make

a cut, raise the saw head and pull it out over

the workpiece without cutting, start the motor,

press the saw head down and push the saw

through the workpiece. Cutting on the pull stroke is

likely to cause the saw blade to climb on top of the work-

piece and violently throw the blade assembly towards the

operator.

e) Never cross your hand over the intended line of

cutting either in front or behind the saw blade.

Supporting the workpiece “cross handed” i.e. holding the

workpiece to the right of the saw blade with your left hand

or vice versa is very dangerous.

f) Do not reach behind the fence with either hand

closer than 100 mm from either side of the saw

blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity

of the spinning saw blade to your hand may not be obvi-

ous and you may be seriously injured.

Parkside 360564 - IAN 360564 Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info