Bedienungsanleitung Parkside 360564 - IAN 360564 (Seite 12 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch)

763673

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

7GB/IE

23 Replace table inserts when worn!

24 Avoid overheating of the saw teeth.

25 When sawing plastic, avoid melting of the plastic.

Use the appropriate saw blades for this purpose. Replace

damaged or worn saw blades immediately.

When the saw blade overheats, stop the machine. Allow

the saw blade to cool down before using the machine

again.

Attention: Laser radiation

Do not stare into the beam

Class 2 laser

Protect yourself and you environment from acci-

dents using suitable precautionary measures!

• Do not look directly into the laser beam with unprotected

eyes.

• Never look into the path of the beam.

• Never point the laser beam towards reﬂecting surfaces and

persons or animals. Even a laser beam with a low output

can cause damage to the eyes.

• Caution - methods other than those speciﬁed here can result

in dangerous radiation exposure.

• Never open the laser module. Unexpected exposure to the

beam can occur.

• The laser may not be replaced with a diﬀerent type of laser.

• Repairs of the laser may only be carried out by the laser

manufacturer or an authorised representative.

Residual risks

The machine has been built according to the state

of the art and the recognised technical safety re-

quirements. However, individual residual risks can

arise during operation.

• Health hazard due to electrical power, with the use of im-

proper electrical connection cables.

• Furthermore, despite all precautions having been met, some

non-obvious residual risks may still remain.

• Residual risks can be minimised if the „safety instructions“

and the „Proper use“ are observed along with the whole of

the operating instructions.

• Do not load the machine unnecessarily: excessive pressure

when sawing will quickly damage the saw blade, which re-

sults in reduced output of the machine in the processing and

in cut precision.

• When cutting plastic material, please always use clamps:

the parts which should be cut must always be ﬁxed between

the clamps.

• Avoid accidental starting of the machine: the operating but-

ton may not be pressed when inserting the plug in an outlet.

• Use the tool that is recommended in this manual. In doing so,

your machine provides optimal performance.

• Hands may never enter the processing zone when the ma-

chine is in operation.

• Release the handle button and switch oﬀ the machine prior

to any operations.

Warning! This electric tool generates an electromagnetic ﬁeld

during operation. This ﬁeld can impair active or passive medical

implants under certain conditions. In order to prevent the risk of

serious or deadly injuries, we recommend that persons with medi-

cal implants consult with their physician and the manufacturer of

the medical implant prior to operating the electric tool.

7. Technical data

AC motor....................................................220 - 240 V~ 50 Hz

Power S1* ..................................................................2000 Watt

Idle speed n0

1st gear ........................................................................3200 min-1

2nd gear .......................................................................4500 min-1

Carbide saw blade ...............................ø 255 x ø 30 x 2,2 mm

Number of teeth .......................................................................48

Maximum tooth width of saw blade ..................................3 mm

Swivel range .................................................. -45° / 0°/ +45°

Mitre cut .................................................... 0° bis 45° to the left

Saw width at 90° ................................................. 340 x 90 mm

Saw width at 45° ................................................. 240 x 90 mm

Saw width at 2 x 45°

(double mitre cut) .................................................. 240 x 45 mm

Protection class .................................................................... II /

Weight .......................................................................ca. 14,7 kg

Laser class ...................................................................................2

Wavelength of laser ........................................................ 650 nm

Laser output .....................................................................< 1 mW

* S1 operating mode, continuous duty

The work piece must have a minimum height of 3

mm and a minimum width of 10 mm.

Make sure that the workpiece is always secured

with the clamping device.

Noise

Total noise values determined in accordance with EN 62841.

Sound pressure level LpA ............................................ 97,2 dB(A)

Uncertainty KpA ......................................................................3 dB

Sound power level LWA ............................................ 110,2 dB(A)

Uncertainty KWA .....................................................................3 dB

Wear hearing protection.

The eﬀects of noise can cause a loss of hearing

The above-mentioned noise emission values were measured in

accordance with a standardised test procedure and can be

used to compare one power tool with another.

The above-mentioned noise emission values can also be used

for the preliminary assessment of exposure.

Warning:

• The noise emissions during the actual use of the power tool

may diﬀer from the above-mentioned values depending on

the power tool being used, in particular on the type of work-

piece being processed.

• Try to keep emissions as low as possible. For example: Limit

your working time. In this regard, all the operational cycle

phases must be taken into consideration (such as the times

when the tool is switched oﬀ or running idle).

Parkside 360564 - IAN 360564 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info