Bedienungsanleitung Parkside 360564 - IAN 360564 (Seite 13 von 140) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Spanisch, Polnisch)

763673

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

8GB/IE

8. Before starting the equipment

• Open the packaging and remove the device carefully.

• Remove the packaging material as well as the packaging

and transport bracing (if available).

• Check that the delivery is complete.

• Check the device and accessory parts for transport damage.

• If possible, store the packaging until the warranty period

has expired.

m DANGER

The device and packaging materials are not toys!

Children must not be allowed to play with plastic

bags, ﬁlm and small parts! There is a risk of swal-

lowing and suﬀocation!

8.1 Mounting the transport handle (ﬁg. 3.1)

ATTENTION! The correct position of the transport handle (39)

is speciﬁed by a groove.

• Mount the transport handle (39) on the machine head (4)

using the Phillips screws 5.0 x 25 mm.

• Then tighten the two Phillips screws 5.0 x 25 mm (40) with a

Phillips screwdriver (not included in the scope of delivery).

8.2 Setting up the machine (ﬁg. 3.2)

• The machine must be set up where it can stand securely.

• Secure the machine on a workbench, base frame or similar.

• Insert 4 screws (not included in the scope of delivery) into

the holes on the ﬁxed saw table (15).

• Tighten up the screws.

8.3 Installing the tilt protection (ﬁg. 3.2)

• Loosen the tilt protection (36) pre-installed at the bottom of

the saw.

• Pull the tilt protection (36) out, so that it can still be ﬁxed

with the aid of the Allen screws.

• Secure the tilt protection again with an Allen key (D).

8.4 Setting the adjustment screw (ﬁg. 3.3)

• Set the adjustment screw (37) to the level of the tabletop to

avoid wobbling of the machine.

8.5 General information

• All covers and safety devices have to be properly ﬁtted be-

fore the equipment is switched on.

• It must be possible for the blade to run freely.

• When working with wood that has been processed before,

watch out for foreign bodies such as nails or screws, etc.

• Before you press the ON/OFF switch check that the saw

blade is ﬁtted correctly. Moving parts must run smoothly.

• Before you connect the equipment to the power supply make

sure the data on the rating plate are identical to the mains

data.

8.6 Checking the moving saw blade guard safety

device (5)

The saw blade guard protects against accidental contact with

the saw blade and from chips ﬂying around.

8.6.1 Check function

To do so, fold the saw downwards:

• The saw blade guard must provide free access to the saw

blade without touching other parts.

• When folding the saw upwards into the starting position, the

saw blade guard must cover the saw blade automatically.

9. Attachment

You need:

1x Allen key 6 mm (C)

1x Allen key 3 mm (D)

(included in the scope of delivery)

1x open-ended spanner 13 mm

1x Phillips screwdriver

(not included in the scope of delivery)

9.1 Attaching the multifunction sliding cross cut mi-

tre saw (ﬁg. 1/2/3.3/4)

• In order to adjust the rotary table (14), fold the locking han-

dle (11) upwards and pull up the latched position lever (35)

with your index ﬁnger.

• Turn the rotary table (14) and pointer (12) to the desired

angle measurement of the scale (13). To ﬁx the setting, fold

the locking handle (11) downwards.

• Press the machine head (4) lightly downwards and remove

the locking bolt (23) from the motor bracket. Thus, the saw

disengages from the lowest position.

• Swing the machine head (4) up.

• It is possible to secure the clamping devices (7) to the left or

right on the ﬁxed saw table (15). Insert the clamping devices

(7) into the holes provided on the back of the stop rail (16)

and secure them with the wing screws (7a).

For 0°- 45° mitre cuts, the clamping device (7) must only be

mounted on the right side (see ﬁg. 14-15).

• It is possible to tilt the machine head (4) a max. 45° to the

left by loosening the set screw (22).

• Workpiece supports (8) must always be secured and used

during work. Deﬁne the desired table size (see 9.1.1.).

9.1.1 Deﬁning the table size

• Loosen the set screw (9).

• Pull out the workpiece support (8) to the desired table size.

• Tighten the set screw (9) again.

9.2 Chip collection bag (ﬁg. 1/5)

The saw is equipped with a chip collection bag (17) for saw-

dust and chips.

Attention! The chip collection bag may only be used when

cutting wood and wood-like materials! When cutting metal,

there is a risk that hot chips will ignite the chip collection bag.

Squeeze the wings of the metal ring on the chip collection bag

(17) together and slide it over the extraction port (17a) near

the engine.

The chip collection bag (17) can be emptied by means of a

zipper at the bottom.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside 360564 - IAN 360564 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info