745332
16
Zoom out
Zoom in
Vorherige Seite
1/122
Nächste Seite
16
GB
IE
- Never operate the device wit-
hout protective equipment.
Keep your hands away from
the disc when the device is in
operation. Risk of injury.
Information on replace-
ment:
Never operate the device without
protective equipment.
Ensure that the rotation speed
stated on the grinding disc (
11) ) is the same or higher than
the nominal rotation speed of the
device.
Ensure that the grinding disc
dimensions match those of the
device.
Only use awless grinding discs
(ringing test: when you strike the
grinding disc with a plastic ham-
mer, it results in a clear sound).
Never re-drill a locating hole
which is too small to make it lar-
ger.
Never use separate bushings or
adapters in order to make grin-
ding discs with a hole that is too
large t the device.
Do not use any saw blades.
To clamp the grinding tools
only use the clamping ange
provided. The pads between
the clamping ange and the
grinding tools must be made of
elastic materials e.g., rubber,
soft cardboard etc.
Always reassemble the device
completely after replacing the
grinding disc.
Switch the device off and remove
the mains plug. Allow the device to
cool down.
Wear protective gloves when chan-
ging the grinding discs in order to
avoid cutting damages.
The grinding disc nut must not be
screwed too tightly in order to avo-
id breaking the disc and nut.
Turning on and off
Make sure that the power supply
voltage matches the voltage rating
indicated on the device‘s type pla-
te.
Connect the machine to the power
supply.
1. Press the on switch (4) to start the de-
vice. Press the on/off switch (5).
2. To turn it off, release the on-off button.
The device turns off.
After switching on the device, wait until the
device has reached its max. speed. Only
then should you start with the work.
The disc still runs even after
the device has been switched
off. Risk of injury.
Trial run:
Always carry out a trial run before carry-
ing out your rst grinding procedure and
after every disc replacement. Switch the
device off immediately if the grinding disc
is not rotating smoothly, if considerable
vibration occurs or if you hear abnormal
noises.
16

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 114254 PWS 125 B2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info