Bedienungsanleitung Parkside IAn 270853 PMGS 12 C3 (Seite 40 von 48) (Französisch)

745535

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

PMGS 12 C3

│

37 ■

e) Always ﬁx the workpiece when using rotary

ﬁles, cutting discs, high-speed milling tools or

hard-metal tools. Even a minimal tilting in the

groove can cause these tools to jam and lead

to a kickback. When cutting disc jams, it usually

breaks. When a rotary ﬁle, high-speed milling

tool or hard-metal milling tool jams, the acces-

sory tool can jump out of the groove and lead

to loss of control of the power tool.

Supplementary safety instructions

for grinding and abrasive cutting

Special safety instructions for grinding and

abrasive cutting

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with the

edge of the disc. Any lateral application of force

on these grinding tools can lead to breakage.

b) Use only undamaged mandrels of the correct

size and length and without undercut on

the shoulder for conical and straight pencil

grinders. Using an appropriate mandrel re-

duces the risk of breakages.

c) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or jamming and

thus the possibility of kickback or breakage of

the grinding tool.

d) Avoid putting your hand in the area in front

of and behind the rotating cutting disc. When

you move the cutting disc away from your hand,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc could be

thrown out directly towards you.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of a

cut. This could lead to kickback. Identify and

remove the cause of the jam.

f) Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

g) Support panels or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides, namely in the

vicinity of the cut, and also at the edge.

h) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The inserted cutting disc may cut into

gas or water pipes, electrical wiring or other

objects that can cause kickback.

Supplementary safety instructions

for working with wire brushes

Special safety instructions for working with

wire brushes:

a) Be aware that the brush can lose wire bristles

even during normal operation. Do not over-

stress the wires by applying excessive pres-

sure to the brush. The wire bristles can easily

penetrate light clothing and/or skin.

b) Allow the brush to run at working speed for

at least one minute before applying it to the

workpiece. Ensure that no one is standing in

front of or in line with the brush during this

time. Loose pieces of wire could ﬂy oﬀ during

the run-in period.

c) Aim the rotating steel brush away from your-

self. When working with these brushes, small

particles and minute pieces of wire can ﬂy oﬀ

at great speed and pierce skin.

Safety instructions for drills

■ Loss of control can lead to injuries.

■ Hold the appliance by the insulated handles

when you are carrying out work during which

the deployed tool may come into contact with

concealed power cables or its own power

cable. Contact with a live cable can also make

metal parts of the appliance live and could

result in an electric shock.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAn 270853 PMGS 12 C3 Seite 40

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAn 270853 PMGS 12 C3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info