745342
9
Zoom out
Zoom in
Vorherige Seite
1/44
Nächste Seite
6
PFS 710 C2
GB
IE
Before use
Fitting/changing the saw blade
WARNING!
Always remove the plug from the power socket
before working on the appliance.
Otherwise, there is a risk of injury.
Turn the quick-release chuck
and hold it in
this position.
Press the required saw blade as far as it will go
into the quick-release chuck
.
Release the quick-release chuck
, it must
return to its initial position. The saw blade is
now locked.
Turning the handle
RISK OF INJURY!
Always remove the plug from the power socket
before working on the appliance. The handle
can be turned by 90° to the right or left.
This allows the ON / OFF switch to be
turned to a most suitable position depending
on the working condition.
Press the release button
and turn the handle
to the right or left.
Allow the handle
to engage.
Adjusting the footplate
RISK OF INJURY!
Always remove the plug from the power
socket before working on the appliance.
Adjust the footplate
according to the cutting
depth.
To do so, loosen the locking lever
and move
the footplate to the corresponding position.
Lock this position by tightening the locking lever
.
Stroke rate selection
Use the adjusting wheel to select the desired
stroke rate (– = lower stroke rate, + = increased
stroke rate).
The stroke rate can also be changed during opera-
tion.
Operation
Switching on and off
During operation, you can choose between instan-
taneous and continuous operation.
Switching to instantaneous operation:
Press the ON / OFF switch
. The working
light comes on with a slightly or fully pressed
ON /OFF switch and illuminates the work-
ing area in poor lighting conditions.
Switching off instantaneous operation:
Release the ON / OFF switch
.
Switching to continuous operation:
Press the ON / OFF switch
and lock it in this
position with the locking switch .
Switching off continuous operation:
Press the ON / OFF switch
and release it
again.
Guiding the sabre blade safely
To adapt to the workpiece and for safe placement,
the footplate can be swivelled. It must always
make contact with the workpiece when the appli-
ance is running.
Practical advice on sawing
Check the material to be worked to make sure
that all foreign objects have been removed, e.g.
nails, screws, etc..
Ensure that the ventilation slits are not covered.
9

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 272950 PFS 710 C2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info