Bedienungsanleitung Parkside IAN 273280 PFBS 160 A1 (Seite 45 von 50) (Französisch)

745330

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

45 GB

Start-up

First slide the tool you wish to use through the

clamping nut

before inserting it into the

collet

ﬁtting the tool shaft.

Press and hold the spindle lock

Insert the collet

into the threaded insert,

then tighten the clamping nut

using the

combination wrench

on the thread.

Using a tool with clamping mandrel:

Use the screwdriver end of the combination

wrench

to loosen and tighten the screw on

the clamping mandrels.

Insert the clamping mandrel in the tool as de-

scribed.

Using the combination wrench

, loosen the

screw on the clamping mandrel.

Insert the attachment you wish to use onto the

screw between two washers.

Use the combination wrench

to tighten the

screw on the clamping mandrel.

Brick

Do not resharpen any edges by hand with

the brick

Installing sanding belts

Slide the grinding belt

onto the grinding man-

drel

from the top. Tighten the screw on the grind-

ing mandrel

to secure the grinding belt

Attaching polishing tools

Turn the polishing attachment

on the point

of the mandrel for polishing attachments

Switching on and oﬀ /

Adjusting the speed

Switching on / adjusting the speed:

Set the ON / OFF switch

to position „I“ by

pressing down and sliding it forward.

Set the variable speed control

to a position

between „1“ and „MAX“.

Switching off:

Set the ON / OFF switch

to position „0“.

Using the grip collar with LED light

Hold the spindle lock

and unscrew the

clamping nut

from the thread, turning coun-

ter-clockwise.

Release the spindle lock

Then screw the union nut

anti-clockwise from

the thread.

Screw the grip collar with LED light

onto the

thread, turning clockwise.

Hold the spindle lock

and screw the clamp-

ing nut

onto the thread, turning clockwise.

Release the spindle lock

Set the ON / OFF switch of the LED light

position “I“ to switch it on (see Fig. C).

Set the ON / OFF switch of the LED light

position “0“ to switch it oﬀ again.

Repeat the steps in reverse order to reattach the

union nut

Information about processing

materials / tool / speed range

Use the router bits to process wood, plastic and

sheetrock at maximum speed.

Determine the speed range for processing zinc,

zinc alloys, aluminium, copper and lead by

testing scrap pieces.

Process plastics and materials with a low melt-

ing point at a low speed.

Process wood at high speeds.

Clean, polish and buﬀ at a medium speed.

Note: The milling bit

is not intended for use on

steel or iron. Suitable milling bits are available.

The following information are non-binding recom-

mendations. When performing the actual work also

test yourself, which tools and settings are ideal for

the material you are working on.

General power tool safety warnings / Start-up

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 273280 PFBS 160 A1 Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 273280 PFBS 160 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info