Bedienungsanleitung Parkside IAN 273280 PFBS 160 A1 (Seite 47 von 50) (Französisch)

745330

Zoom out

Zoom in

Vorherige Seite

1/50

Nächste Seite

47 GB

Start-up

Store accessories inside the original box or oth-

erwise protect the accessories from damage.

Store accessories dry and away from aggres-

sive media.

Tips and tricks

Applying excessive pressure can cause the in-

stalled tool to break and / or damage the work

piece. Optimal results can be achieved by ap-

plying the tool to the work piece at a steady

speed range and little pressure.

Hold the device with both hands whilst cutting.

Please note the data and information in the

chart to prevent the spindle end touching the

perforated plate of the grinding tool.

Flexible shaft

Never use the spindle lock with the motor on.

The tool or the ﬂexible shaft could otherwise

be damaged.

Unscrew the union nut

from the tool, turning

counter-clockwise, and put aside.

Press and hold the spindle lock

Unscrew the clamping nut

from the tool,

turning counter-clockwise.

Attach the ﬂexible shaft

to the tool, inserting

the inner axle on the ﬂexible shaft along with

the clamping nut

into the collet

Use the combination wrench

to ﬁrst tighten t

clamping nut

, then the union nut

14 b

of the

ﬂexible shaft

to the tool, turning clockwise.

Now insert the accessory you wish to use into

the collet

of the ﬂexible shaft.

To lock the spindle, slide back the black sleeve

on the ﬂexible shaft.

Using the combination wrench

, open the

collet holder

on the ﬂexible shaft, insert the

accessory and tighten the collet holder

Stretch stand for the

multi-function tool (Fig. J)

Screw the stretch stand

into the clamp

Note: The stretch stand

can be screwed

into the clamp in two diﬀerent positions, de-

pending on the whether you‘re attaching to a

horizontal or vertical surface.

Secure the clamp

at the edge of a work-

bench or a work table no thicker than 55 mm.

The stretch stand

is height adjustable. Loosen

the upper tube of the stretch stand

by turning

to the left (–). Extend the tube to the maximum

height and secure by turning to the right (+).

The holder

is also height adjustable, simple

turn the black thread to the left. After adjusting

the holder to the correct height, turn the thread

in the opposite direction to tighten.

Secure the tool to the holder

of the stretch

stand

with the metal bracket

. This hold-

rotates by 360°.

Base assembly

Using the attachment, the tool is particularly suited

for cutting special shapes (holes for sockets, etc.).

Attach the milling bit

as described in chapter

„Attaching / changing the tool / collet“.

Ensure that the bit’s shaft protrudes from collet

by approx. 13 mm.

Unscrew the union nut

from the tool, turning

clockwise, and put aside.

Screw the base

onto the unit.

To set the correct working depth, loosen the

locking screw

and adjust the bottom of the

base assembly to the desired size.

Then tighten the locking screw

Start-up

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 273280 PFBS 160 A1 Seite 47

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 273280 PFBS 160 A1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info