Bedienungsanleitung Parkside IAN 273460 PTK 2000 B2 (Seite 44 von 204) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch)

745555

Zoom out

Zoom in

Vorherige Seite

1/204

Nächste Seite

GB IE

Caution! Both stand brackets

must be attached to the rear

of the machine at attachment

points 38!

8. Then tighten all of the bolts and nuts of

the base.

Mounting the table width



(Figures 11-14)

1. Loosely tighten the table width extensi-

on (7) and table length extension (15)

on the saw table using the hexagon

bolts (f). (Figure 12).

2. Loosely tighten the table supports

(25, 26) on the housing of the table

circular saw using hexagon bolts (f). In

addition, the table supports (25, 26)

also have to be loosely tightened to

the table width and length extensions.

Mounting material: Hexagon bolts (e),

washer (a) and nut (c). The short sup-

ports (25) are for the table widening

extension, the long supports (26) for

the length extension, (Figures 13, 14).

3. Turn the saw over with the base and



4. Align the table width and length exten-



5. Then tighten all bolts.

Mounting the Suction

Adapter

(Figure 15)

1. Insert the suction adapter (16) into

the opening provided on the rear of

the machine. The side outlet is now

pointing outwards.

2. The suction adapter has a rubber seal;

make sure that this is mounted.

3. The adapter is secured by means of

a bayonet lock. Insert the vacuum

cleaner adapter (16) as shown in

Figure 15 and lock this in place with a

quarter turn in a clockwise direction.

Mounting the Riving Knife

(Figures 16-19)

Caution! Remove the mains plug!

The setting of the saw blade (5)

must be checked whenever a blade

has been replaced.

1. Inserting the batteries (Figure 16):

- Turn the laser on/off switch (35) to the

0 position (laser off).

- Remove the battery compartment cover

(37) by loosening the screw (36).

Now remove the battery compartment

cover (37) by bending at the side.

- Insert the batteries supplied (type

AAA), ensuring the correct polarity

(see Figure 16).

- Put the battery compartment cover (37)

back in position and tighten it with

the screw (36). Notes concerning the

batteries:

- If you are not going to use the laser

for a prolonged period, please remove

the batteries from the battery com-

partment. Otherwise, the leaking of



- Do not place the batteries on radia-

tors or expose them for a prolonged

period to strong sunlight; temperatures

above 50° could damage the device.

2. Adjust the saw blade (5) to a max.

cutting depth, move to the 0° position

and lock in place.

3. Release the screws (29). Remove the

table insert (6) (Figure 17).

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 273460 PTK 2000 B2 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info