Bedienungsanleitung Parkside IAN 275389 PWS 125 C3 (Seite 12 von 90) (Deutsch, Englisch, Holländisch, Dänisch)

745528

Zoom out

Zoom in

Vorherige Seite

1/90

Nächste Seite

GB IE NI

consult their doctor and the manu-

facturer of their medical implant

before operating the machine.

Additional safety instructions

for all applications

Kickback and corresponding

precautions

Kickback is the sudden reaction from a

chopping or blocked grinder attachment

such as a grinding disc, grinding plate,

wire brush etc. Chopping or blocking leads

to sudden stopping of the rotating attach-

ment. This causes an uncontrolled electric

tool to accelerate in a direction counter to

the rotational direction of the attachment

tool. If, for example, a grinding disc cuts

into the workpiece or blocks it, the edge of

the grinding disc that digs into the work-

piece can get caught and, through that,

break off the grinding disc or cause a kick-

back. The grinding disc then moves towards

or away from the operator, depending on

the direction of rotation of the disc at the

blocked spot. Here, the grinding discs can

also break. A kickback is caused by wrong-

ly or incorrectly operating the electric tool.

It can be avoided by suitable cautionary

measures, such as described below.

a) Hold the electric tool very rmly and

bring your body and your arm into a

position in which you can resist the kick-

back force. Always use the supplemental

handle if available to give you the best

control over kickback force or reaction

time during acceleration. The operator

can master the kickback and reaction

force through suitable precautions.

b) Never bring your hands near a rotating

attachment tool. The attachment tool

can run over your hand in the kickback.

c) Keep your body away from the area

in which the electric tool would move

during a kickback. The kickback drives

the electric tool in the counter-direction

to the rotation of the grinding disc at

the blocked spot.

d) Work particularly cautiously in corner

areas or where there are sharp cor-

ners etc. Prevent the attachment tools

from recoiling from the workpiece and

jamming. The rotating attachment tool

tends to jam when near corners, sharp

edges or when it recoils from such. This

causes a loss of control or kickback.

e) Do not use chain or toothed saw bla-

des. Such attachment tools frequently

cause a kickback or loss of control over

the electric tool.

Special safety instructions for

grinding and cutting

a) Use only grinders which have been

approved for your electric tool and the

protective hood intended for these grin-

ders. Grinders which are not intended

for the electric tool may not be sufci-

ently shielded and are unsafe.

b) Depressed Center grinding wheels must

be pre-assembled so that their surface

not above the level of the edge of the

guard stands out. An improperly moun-

ted grinding wheel, which extends bey-

ond the level of the edge of the guard,

not sufciently shielded.

c) The protective hood must be securely

attached to the electric tool and adjus-

ted so that the greatest level of safety

is reached, i.e., the smallest possible

amount of the grinder is exposed to the

operator. The protective hood should

protect the operator from broken bits

and accidental contact with the grinder.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 275389 PWS 125 C3 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Parkside IAN 275389 PWS 125 C3

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info