Bedienungsanleitung Parkside IAN 275685 PDMH 4500 A3 (Seite 6 von 72) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

745549

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

7 GB/IE

Introduction / General safety instructions for air tools

Technical Data

Max. working pressure: 6.3 bar

Percussion rate: 3500 rpm

Chisel holder: 11 mm

Weight:

Hammer: 1390 g

Noise and vibration

Noise and vibration ratings were determined according

to EN 15744 and EN 28927-9.

Noise level L

: 96.8 dB(A)

Uncertainty K

: 3 dB

Sound power level L

: 107.8 dB(A)

Uncertainty K

: 3 dB

Wear hearing protection!

Exposure to noise can cause hearing loss.

Vibration

Vibration emission value a

= 6.14 m / s

Uncertainty K = 1.5 m / s

Additional information

The vibration emission value speciﬁed was measured

according to a standardised testing method and may

vary depending on the method the tool is being used,

and in exceptions be higher than the speciﬁed value.

The vibration emission value speciﬁed can be used

to compare tools.

The vibration emission value speciﬁed can also serve

as a preliminary assessment of the impact.

General safety

instructions for air tools

Note: When used in the following text, the terms

„compressed air unit“ or „device“ refer to the com-

pressed air unit speciﬁed in these instructions for use.

Basic safety measures must be

followed when using compressed air devices to elim-

inate the risk of ﬁre, electric shock and personal in-

jury. Be sure to read and follow the notices within

these instructions for use prior to using the equipment

and store them in a safe location. The manufacturer

assumes no liability for damages or personal injury

resulting from failure to follow these instructions for use.

Persons (including children) who lack the knowl-

edge or experience to use the tool or whose

physical, sensory or intellectual capacities are

limited must never be allowed to use the tool

without supervision or instruction by a person

responsible for their safety.

Ensure children do not play with the device.

RISK OF INJURY! Before

performing maintenance tasks, disconnect the

compressed air supply.

XPLOSION HAZARD! Never u

petrol or other ﬂammable liquids to

clean the air tool! Sparks could ignite

residual vapours inside the compressed air unit

resulting in the compressed air unit exploding.

Do not use the device in explosive environments

with ﬂammable liquids, gasses or dust. Never

work on materials which are or could potentially

be highly ﬂammable or explosive.

Only use the equipment in areas of application

for which it was designed!

Do not overburden the device.

Never use hydrogen, oxygen, carb

dioxide or other bottled gasses to

power this tool as doing so may re-

sult in an explosion and thus may cause severe

injuries.

Regularly maintain and clean the device as

speciﬁed (see chapters „Maintenance“ and

„Cleaning and care“).

Inspect the device for any damage before use.

Always make sure that the device is in perfect

condition each time before use.

Always be attentive! Unexpected movement of

the device may cause hazards.

Avoid placing your body in an unnatural positi

on.

Keep proper footing and balance at all times.

By doing this you will be in a better position to

Introduction

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 275685 PDMH 4500 A3 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info