745542
14
Zoom out
Zoom in
Vorherige Seite
1/60
Nächste Seite
PDWS 125 A1
GB
IE
 11
Operation
Operating a compressed air tool
NOTE
In order to achieve the full power available
from your compressed air tool, always
use compressed air hoses with an internal
diameter of at least 9 mm. A lower internal
diameter can considerably reduce the power.
CAUTION!
Do not use a compressed air line that con-
tains any water condensation.
The tool must be sufficiently supplied with
pneumatic oil to ensure long service life. This
can take place as follows:
Use oiled compressed air by fitting a mist
lubricator.
Without a mist lubricator: add oil manu-
ally through the compressed air connec-
tion
every day. Approx. 3-5 drops
of pneumatic oil for every 15 operating
minutes during continuous use.
If the tool has been out of operation for sev-
eral days, add around 5 drops of pneumatic
oil manually through the compressed air
connection .
Allow the tool to run at idling speed for a
short time.
Always guide the machine using both hands.
Switch on first, then apply the accessory tool
to the workpiece.
After switching off, only put the machine down
once the motor has come to a standstill.
1.) Attach a suitable accessory tool.
2.) Adjust the operating pressure (measured
at the air intake when the compressed air
tool has been switched on). Please refer to
the section entitled "Technical data" for the
maximum permissible operating pressure
3.) Connect the compressed air tool to the com-
pressed air supply.
4.) Switching on: Push the safety lock-out
towards and press the ON/OFF switch .
5.) Switching off: Release the ON/OFF switch
.
Working procedures
Sanding:
Press the machine against the workpiece moder-
ately and move it backwards and forwards over
the surface so that the workpiece surface does
not become too hot.
Rough grinding:
Work using an angle of incidence of between
30° and 40° for good working results.
NOTE
Never use cutting discs for rough grinding.
Abrasive cutting:
Always work against abrasive cutting (see Fig-
ure 3). Otherwise there is a risk that the ma-
chine can jump out of the cut in an uncontrolled
manner. Work using moderate forward speed
appropriate to the material being processed.
Do not tilt, do not press, do not oscillate.
Fig. 3
NOTE
Never use rough grinding discs for cutting.
14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 276009 PDWS 125 A1 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info