Bedienungsanleitung Parkside IAN 276009 PDWS 125 A1 (Seite 12 von 60) (Deutsch, Englisch, Holländisch, Französisch)

745542

Zoom out

Zoom in

Vorherige Seite

1/60

Nächste Seite

PDWS 125 A1

│

9 ■

If this happens, an uncontrolled compressed

air tool turns rapidly against the direction of

rotation of the accessory tool caught in the

blockage.

■ If, for example, a grinding disc catches or jams

in a workpiece, the edge of the grinding disc

that is projecting into the workpiece can get

caught and break oﬀ the grinding disc or cause

a kickback. The grinding disc can then ﬂy in

the direction of the operator or away from him,

depending on the direction of rotation of the

disc at the blockage.

This can also break grinding discs.

■ A kickback is caused by incorrect use or misuse

of the compressed air tool. This can be avoided

by taking proper precautions as given below.

a) Hold the compressed air tool ﬁrmly

in both hands and position your body and

arms so they can absorb the force of a

kickback. Always use the auxiliary handle,

if available, so you have maximum control

over the kickback force or reaction torques

at full speed. By taking adequate precau-

tions, the operator can stay in control of the

kickback and reaction torques.

b) Never hold your hand close to rotat-

ing accessory tools. The accessory tool

could move across your hand in the event

of a kickback.

c) Keep all parts of your body outside

the region in which the compressed air tool

is likely to move in event of a kickback. The

kickback will force the compressed air tool

in the opposite direction to the direction of

rotation of the grinding disc at the block-

age.

d) Take special care when working

around corners, sharp edges, etc. Avoid

allowing the accessory tool to bounce back

from the workpiece, or jam. The rotating ac-

cessory tool is more likely to jam in corners

or sharp edges or if it bounces. This can

cause a loss of control or kickback.

e) Do not use chains or toothed saw

blades. Such accessories often cause a kick-

back or loss of control over the power tool.

Operation

NOTE

► Screw the plug nipple

on before ﬁrst use.

Attaching the auxiliary handle

CAUTION!

► Do not work with the tool if the auxiliary

handle

is not attached!

♦ Screw the auxiliary handle

ﬁrmly onto the

left-hand or right-hand side of the machine.

Attaching the protective cover

CAUTION!

► For safety reasons, always use the protective

cover

■ The protective cover

is mounted on delivery

with 2 screws on the device.

♦ For rotation of the protective cover

, you ﬁrst

remove all screws with the hex key .

♦ Replace the protective cover

at most by a

hole added to the new position.

The closed side of the protective cover must

always be facing to the operator.

✓

✗

♦ Attach the protective cover with 3 screws on

the device.

Screw the remaining screw into the threaded

hole.

♦ Check for secure seating: The protective cover

must be securely attached.

Only use accessory tools

which the protective

cover protrudes be-

yond by at least 2 mm.

WARNING!

► The supplied protective cover

is for grinding

disc use only.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 276009 PDWS 125 A1 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info