Bedienungsanleitung Parkside IAN 279872 PFBS 12 A1 (Seite 11 von 66) (Deutsch, Englisch, Holländisch, Französisch)

745925

Zoom out

Zoom in

Vorherige Seite

1/66

Nächste Seite

PFBS 12 A1

■ 8

│

Supplementary safety instructions

for grinding and abrasive cutting

Special safety instructions for grinding and

abrasive cutting

a) Use only the grinding accessories approved

for your power tool and only for the recom-

mended applications. Example: Never grind

with the side surface of a cutting disc. Cutting

discs are designed to remove material with the

edge of the disc. Any lateral application of

force on these grinding tools can lead to break-

age.

b) Use only undamaged mandrels of the correct

size and length and without undercut on

the shoulder for conical and straight pencil

grinders. Using an appropriate mandrel re-

duces the risk of breakages.

c) Avoid cutting disc jams or excessive contact

pressure. Do not make any excessively deep

cuts. Overloading the cutting disc increases the

stress and likelihood of tilting or jamming and

thus the possibility of kickback or breakage of

the grinding tool.

d) Avoid putting your hand in the area in front

of or behind the rotating cutting disc. When

you move the cutting disc away from your hand,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc could be

thrown out directly towards you.

e) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steady until the

disc has completely stopped turning. Never

attempt to pull a rotating cutting disc out of

a cut. This could lead to kickback. Identify and

remove the cause of the jam.

f) Do not switch the power tool back on as long

as it is in the workpiece. Allow the cutting disc

to reach its full speed before you carefully

continue the cut. Otherwise, the disc may jam,

jump out of the workpiece or cause kickback.

g) Support panels or large workpieces to reduce

the risk of the cutting disc jamming and caus-

ing a kickback. Large workpieces can bend

under their own weight. The workpiece must be

supported on both sides, namely in the vicinity

of the cut, and also at the edge.

h) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The inserted cutting disc may cut into

gas or water pipes, electrical wiring or other

objects that can cause kickback.

Supplementary safety instructions

for working with wire brushes

Special safety instructions for working with

wire brushes:

a) Be aware that the brush can lose wire bristles

even during normal operation. Do not over-

stress the wires by applying excessive pressure

to the brush. The wire bristles can easily penet-

rate light clothing and/or skin.

b) Allow the brush to run at working speed for

at least one minute before applying it to the

workpiece. Ensure that no one is standing in

front of or in line with the brush during this

time. Loose pieces of wire could ﬂy oﬀ during

the run-in period.

c) Aim the rotating steel brush away from your-

self. When working with these brushes, small

particles and minute pieces of wire can ﬂy oﬀ

at great speed and pierce skin.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 279872 PFBS 12 A1 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info