Bedienungsanleitung Parkside IAN 280250 PWS 125 D3 (Seite 13 von 114) (Deutsch, Englisch, Holländisch, Dänisch, Französisch)

746143

Zoom out

Zoom in

Vorherige Seite

1/114

Nächste Seite

1 3

NIIEGB

Other special safety instructions

for cutting grinding

a) Avoid blocking the cutting disc or pres-

sing down too hard. Do not make any

excessively deep cuts. Overloading the

cutting disc increases wear and its ten-

dency to tilt or block and, with that, to

kickback or break the grinder.

b) Avoid the area in front of and behind

the rotating cutting disc. When you

move the cutting disc by itself in the

workpiece, in the event that the electric

tool kicks back with the rotating disc, it

can spin directly towards you.

c) If the cutting disc jams, or you interrupt

your work, switch the device off and

hold it until the disc has come to a full

stop. Never try to pull the cutting disc

out of the cut while it is still running,

because it can kick back. Identify and

correct the cause of the jamming.

d) Do not switch the electric tool on again

as long as it is in the workpiece. Allow

the cutting disc to rst reach its full

rotational speed before you carefully

resume with the cutting. Otherwise, the

disc may catch, spring away from the

workpiece or cause a kickback.

e) Support plates or workpieces to reduce

the risk of kickback from a jammed cut-

ting disc. Large workpieces may bend

under their own weight. The workpiece

must be supported on both sides of the

disc, near the cutting disc as well as

also at the edge.

f) Be particularly careful for pocket cuts in

existing walls or other areas where you

cannot see what is there. The cutting

disc may cause a kickback when it cuts

into gas or water lines, electrical lines

or other hidden objects.

Additional safety instructions

for sanding

Special safety instructions for

sanding:

• Do not use overly large sand-

paper sheets; follow the

manufacturer‘s information for

sandpaper sizes. Sandpaper sheets

which extend beyond the sanding plate

can cause injuries and can block, tear

the sandpaper, or cause kickback.

Additional safety instructions

for polishing

Special safety instructions for

polishing:

• Let no loose parts of the poli-

shing bonnet, particularly at-

tachment strings. If you shorten

the fastening cords verse defrost

oder. Loose, revolving attachment

strings can capture your ngers or be-

come entangled in the workpiece.

Additional safety instructions

for working with wire brushes

Special safety instructions for

working with wire brushes:

• Be aware that the wire brushes

also lose wire pieces during typi-

cal use. Do not overload the wi-

res by pressing down too hard.

Flying wire pieces can very easily penet-

rate thin clothing and/or your skin.

• If a protective hood is recom-

mended, do not allow the wire

brushes and the protective hood

to touch each other. The diameter

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 280250 PWS 125 D3 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info