Bedienungsanleitung Parkside IAN 282494 PWSA 20 Li A1 (Seite 33 von 134) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

746159

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

PWSA 20-Li A1

■ 28 │ GB

│

Working procedures

NOTE

► Grinding tools should only be used for the

recommended applications. Otherwise, they

can break, be damaged or cause injuries.

Rough grinding:

Never use cutting discs for rough

grinding!

■ Move the angle grinder with moderate pres-

sure back and forth over the workpiece.

■ For soft material, move the rough grinding

disc at a shallow angle over the workpiece;

for hard material at a slightly steeper angle.

Abrasive cutting:

Never use rough grinding discs for

cutting!

■ Use only tested ﬁbre-reinforced cutting or

grinding discs that are approved for a circum-

ferential speed of not less than 80 m/s.

CAUTION!

The grinder continues running after being turned

oﬀ. Do not try to brake it by applying lateral

counterpressure.

■ Secure the workpiece! Use clamps/a vice to

hold the workpiece ﬁrmly in place. This is much

safer than simply holding it in your hand.

■ Always switch oﬀ the appliance before put-

ting it away and wait for the appliance to

come to a complete standstill.

■ Use the appliance only for dry cutting or

sanding.

■ The additional handle

must be mounted on

the appliance for all work.

■ Materials containing asbestos may not be

processed. Asbestos is a known carcinogen.

Tip! This symbol indicates proper

behaviour.

HAZARD! ALWAYS GUIDE THE

APPLIANCE THROUGH THE

WORKPIECE IN REVERSE ROTATION.

► In the opposite direction there is a risk of

kickback. The appliance can be pushed out

of the cut.

■ Always switch the appliance on before apply-

ing it to the workpiece. After completing the

task, lift the appliance from the workpiece and

then switch it oﬀ.

■ Always hold the appliance ﬁrmly with two

hands while working.Ensure that your stance

is secure and stable.

■ For an optimum grinding eﬀect, move the ap-

pliance evenly at an angle of 15° to 30° (be-

tween grinding disc and workpiece) backwards

and forwards.

■ When working on angled surfaces, do not

exert great force on the workpiece. If the

rotational speed drops signiﬁcantly, you must

reduce the pressure exerted to allow safe and

eﬀective working. If the appliance suddenly

brakes completely or jams, it must be switched

oﬀ immediately.

■ Cutting: Work at a moderate feed rate and

do not tilt the cutting disc.

■ Roughing and cutting discs become very

hot – let them cool down completely before

touching them.

■ Never use the appliance for purposes other

than the ones for which it was designed.

■ Always make sure that the appliance is

turned oﬀ before ﬁtting the battery.

■ In the event of danger, turn oﬀ the appliance

and remove the battery. Ensure that the ap-

pliance is easily and quickly accessible in the

event of an emergency.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 282494 PWSA 20 Li A1 Seite 33

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info