Bedienungsanleitung Parkside IAN 282494 PWSA 20 Li A1 (Seite 31 von 134) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

746159

Zoom out

Zoom in

Vorherige Seite

1/134

Nächste Seite

PWSA 20-Li A1

■ 26 │ GB

│

e) Always use an undamaged clamping ﬂange

of the correct size and shape for the selected

grinding disc. Suitable ﬂanges support the

grinding disc and reduce the risk of disc break-

age. Flanges for cutting discs can be diﬀerent to

ﬂanges for other grinding discs.

f) Do not use worn grinding discs from larger

power tools. Grinding discs for larger power

tools are not designed for the higher rotational

speeds of smaller power tools and so can

break.

Additional special safety instructions

for abrasive cutting

a) Avoid causing blockages to the cutting disc

or high contact pressure. Do not make any

excessively deep cuts. Overloading the cutting

disc increases the stress and likelihood of tilting

or blocking and thus the possibility of a setback

or a breakage of the grinding tool.

b) Avoid the area in front of and behind the

rotating cutting disc. When you move the cut-

ting disc away from yourself in the workpiece,

it is possible, in the event of a kickback, that the

power tool along with the rotating disc might be

thrown out directly towards you.

b) If the cutting disc jams or you stop working,

switch the tool oﬀ and hold it steadily in the

workpiece until the disc has completely stopped

turning. Never attempt to pull a rotating cutting

disc out of a cut. This could lead to kickback.

Identify and remove the cause of the jam.

d) Do not switch the power tool back on while it

is located in the workpiece. Allow the cutting

disc to reach its full speed before you carefully

continue the cut. Otherwise, the disc can jam,

jump out of the workpiece or cause kickback.

e) Support boards or large workpieces to re-

duce the risk of the cutting disc jamming and

causing a kickback. Large workpieces can

bend under their own weight. The workpiece

must be supported on both sides of the disc:

both in the vicinity of the cutting disc and also

at the edge.

f) Be particularly careful when making "pocket

cuts" into existing walls or other obscured

areas. The protruding cutting disc may cut gas

or water pipes, electrical wiring or other objects

that can cause a kickback.

Safety guidelines for battery

chargers

■ This appliance may be used by chil-

dren aged 8 years and above and

by persons with limited physical,

sensory or mental capabilities or

lack of experience and knowledge,

provided that they are under super-

vision or have been told how to use

the appliance safely and are aware

of the potential risks. Do not allow

children to use the appliance as a

toy. Cleaning and user maintenance

tasks may not be carried out by chil-

dren unless they are supervised.

■ To avoid potential risks, damaged

mains cables should be replaced

by the manufacturer, their customer

service department or a similarly

qualiﬁed person.

The charger is suitable for indoor use

only.

WARNING!

■ To avoid potential risks, damaged mains

cables should be replaced by the manufac-

turer, their customer service department or a

similarly qualiﬁed person.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 282494 PWSA 20 Li A1 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info