Bedienungsanleitung Parkside IAN 285202 PDT 40 D3 (Seite 20 von 80) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

746434

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

PDT 40 D3

■ 16

│

Before use

NOTE

► Put on the supplied protective goggles before

each use. Remove the protective ﬁlm from the

goggle lenses before ﬁrst use.

Connecting the compressed air supply

NOTE

► In order to achieve the full power available

from your compressed air tool, always use

compressed air hoses with an internal diame-

ter of at least 9 mm. A lower internal diameter

can considerably reduce the power.

► The appliance may be operated only with

cleaned, atomised-oil air and must not exceed

the maximum working pressure of 8 bar on

the appliance. The compressor must be ﬁtted

with a pressure reducer to regulate the

working pressure.

CAUTION!

► Do not use a compressed air line that contains

any condensate.

► The tool must be suﬃciently supplied with

pneumatic oil to ensure long service life. This

can take place as follows:

– Use oiled compressed air by ﬁtting a mist

lubricator.

– Without a mist lubricator: Add oil ma-

nually via the threaded nipple

every

day. Approx. 1–2 drops of pneumatic

oil for every 15 operating minutes during

continuous use.

► If the tool has been out of operation for sever-

al days, add around 5 drops of pneumatic oil

manually via the threaded nipple

♦ Connect the appliance to a suitable compressed

air source.

♦ 1.) For this purpose, press the quick-release

connection of the compressed air hose (not

included) onto the ¼" threaded nipple

of the compressed air stapler.

The connection locks automatically.

♦ 2.) Now connect the other end of the com-

pressed air hose to the (ﬁlter) pressure

reducer on the compressor.

Filling the magazine

♦ Press the magazine lever and pull back the

magazine cover until it stops.

♦ Place the appropriate fastener material (nails,

see ﬁg. B or staples, see ﬁg. C) in the magazine

. The staples must be placed on the bar of

the magazine .

♦ Slide the magazine cover forwards until it clicks

into place.

Operation

♦ Load the magazine of the compressed air

stapler, as described in the section "Filling the

magazine".

♦ Set the correct working pressure using the

pressure reducing valve (not supplied).

NOTE

■ Make sure that you do not exceed the

maximum working pressure of 8 bar on the

appliance. An excessive working pressure

does not mean increased output; it merely

increases the compressed air consumption

and accelerates appliance wear.

♦ Switch on the compressor.

Run the compressor once until the maximum

tank pressure has been reached and then

switch oﬀ the appliance.

♦ Place the appliance on the workpiece and pull

the trigger

NOTE

■ The compressed air stapler is

equipped with a trigger lock

The fastener material does not leave

the appliance until the opening of the

compressed air stapler is pressed against the

workpiece and the trigger is pressed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 285202 PDT 40 D3 Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info