Bedienungsanleitung Parkside IAN 291791 PEH 30 C3 (Seite 21 von 87) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

748012

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

PEH 30 C3

│

17 ■

d) Store idle power tools out of the reach of

children and do not allow persons unfamiliar

with the power tool or these instructions to

operate the power tool. Power tools are dan-

gerous in the hands of untrained users.

e) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may aﬀect the power tool’s operation. If

damaged, have the power tool repaired be-

fore use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and ac-

cessory tools etc. in accordance with these

instructions, taking into account the working

conditions and the work to be performed.

Use of the power tool for operations diﬀerent

from those intended could result in a hazardous

situation.

h) Keep handles and grasping surfaces dry,

clean and free from oil and grease. Slippery

handles and grasping surfaces do not allow for

safe handling and control of the tool in unex-

pected situations.

5. Service

a) Have your power tool serviced by a qualiﬁed

repair person using only identical replace-

ment parts. This will ensure that the safety of

the power tool is maintained.

Appliance-speciﬁc safety instructions

for power planers

■ Wait until the cutter block comes to a complete

standstill before putting down the power tool.

An exposed, rotating cutter block can catch in

the surface and cause a loss of control which

could result in serious injuries.

■ Hold the power tool by the insulated handles as

the cutter block can come into contact with its

own power cable. Contact with a live wire may

make exposed metal parts of the power tool live

and could give the operator an electric shock.

■ Fix and secure the workpiece to a sturdy work

surface using clamps or other methods. If you

hold the workpiece in your hands or against

your body only it will remain unstable, and this

can result in loss of control.

■ Wait until the cutter block

comes to a com-

plete standstill before putting down the appli-

ance. An exposed cutter block can catch in the

surface and cause a loss of control which could

result in serious injuries.

■ Do not insert your ﬁngers into the chip ejector

. You can injure yourself on rotating parts!

■ Always switch the appliance on before apply-

ing it to the workpiece. Otherwise, there is a

risk of kickback if the planing blade catches in

the workpiece.

■ The plane sole

must lie ﬂat on the work-

piece when working. Otherwise, there is a risk

of injury due to the plane jamming.

■ Never plane over metal objects. The planing

blade/cutter block

could be damaged.

■ Secure the workpiece. Use clamps/a vice to

hold the workpiece ﬁrmly in place. This is safer

than simply holding it in your hand.

■ Materials containing asbestos may not be

processed. Asbestos is a known carcinogen.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 291791 PEH 30 C3 Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info