Bedienungsanleitung Parkside IAN 291791 PEH 30 C3 (Seite 24 von 87) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

748012

Zoom out

Zoom in

Vorherige Seite

1/87

Nächste Seite

PEH 30 C3

■ 20

│

♦ Replace the planing blade

when both cutting

edges are blunt.

♦ Do not try to sharpen the planing blade

Turn the planing blade

or replace it.

NOTE

► Do not undo the two hex socket screws.

These are used for adjusting the height of

the cutter block. Adjustment is only required

if you are using a diﬀerent type of planing

blade, e.g. a rustic blade.

When changing the blade, always replace

both blades to prevent an imbalance.

► First, unscrew only one blade. This will allow

you to orient your self on the factory-mounted

second blade when reassembling later.

♦ Use the supplied open-ended spanner

undo the 3 fastening screws for the planing

blade .

♦ Push the movable cutter block guard

into

the slot in the housing.

♦ Push the clamping element

upwards out of

the cutter block .

♦ Remove the tensioning plate

20a

from the clamp-

ing element . Remover the planing blade

from the clamping element .

♦ Fit either a new or turned blade in the reverse

order.

♦ Planing blades

can be purchased from the

address given below (see section “Service”).

Replacing the drive belt (see ﬁg. E)

WARNING! RISK OF INJURY

► Always remove the plug from the power

socket before working on the appliance.

♦ Remove the screws

and detach the drive

belt cover .

♦ Remove the worn drive belt

♦ Fit the new drive belt

onto the small belt

wheel ﬁrst and then turn the drive belt

and pull it onto the large belt wheel .

♦ Replace the drive belt cover

and ﬁx it in

place using the screws

Maintenance and cleaning

WARNING! RISK OF INJURY

► Always remove the plug from the power

socket before working on the appliance.

♦ Keep the appliance and the ventilation slits

clean to ensure fault-free operation.

♦ Clean the chip ejector

regularly.

♦ To clean a blocked chip ejector, use a suitable

tool (e.g. a piece of wood, compressed air,

etc.).

♦ Use a dry cloth to clean the housing.

♦ Use a brush to remove any dust stuck to the

appliance.

♦ Never use sharp objects, petrol, solvents or

cleansers which can damage plastic. Do not

allow any liquids to get into the interior of the

appliance.

NOTE

► Replacement parts not listed (such as carbon

brushes, switch) can be ordered via our

service hotline.

Disposal

The packaging consists of environmentally

friendly material. It can be disposed of in

the local recycling containers.

Do not dispose of power tools in

your normal domestic waste!

European Directive 2012/19/EU requires that

worn-out power tools be collected separately and

recycled in an environmentally compatible manner.

Your local community or municipal authorities can

provide information on how to dispose of the ap-

pliance.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 291791 PEH 30 C3 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info