Bedienungsanleitung Parkside IAN 292193 PDTS 6.3 A1 (Seite 32 von 117) (Deutsch, Englisch, Holländisch, Französisch, Spanisch)

746858

Zoom out

Zoom in

Vorherige Seite

1/117

Nächste Seite

GB/IE/NI32

Operation

of connecting to the compressed air system, and

tool effectiveness and life is extended as a result.

Connecting sleeve

Compressed air hose

Quick release connector Compressor

Pressure regulator

Oiler Filter

Quick release connector

Before first use and thereafter at regular intervals,

apply a few drops of pneumatic equipment or

motor oil SAE 10-20 into the compressed air

connection on the pneumatic device. After every

3–4 operating hours, use the assembly key to

remove the screw plug

in the oil reservoir.

Fill the oil reservoir with pneumatic equipment or

motor oil SAE 10-20, and insert the screw plug

back. Wrap some Teflon sealing tape around the

thread on the air connections. Screw the air con-

nections into the pneumatic devices.

 Starting up

Put on protective clothing and goggles.

OTHERWISE THERE IS DANGER OF INJURY!

Check that the parting disc has been tightened

securely.

Check that the workpiece is supported or has been

locked in place correctly. A C clamp is recom-

mended on loose workpieces.

Make sure that generated sparks do not pose any

danger, i.e. they cannot contact any persons or

ignite flammable substances.

Connect the compressed air supply. To do so, con-

nect the compressed air source to the compressed

air connection.

Press the switch ON guard towards the chuck.

Press the trigger arm, and perform the cutting work.

The device rotates at the maximum speed when the

trigger arm is tightened to the stop. Regulate the

tightening pressure and therefore the speed for the

optimal grinding results.

 Switching OFF

Release the trigger arm

to switch OFF the

pneumatic angle grinder.

After work, disconnect the device from the

compressed air source.

Note: First detach the hose from the compressed

air source, and then remove the supply hose from

the device. This prevents the supply hose from

whirling out of control.

 Maintenance

If the machine is to enjoy a long service life and

operate without problems, it is important that the

following maintenance instructions are followed.

The pneumatic angle grinder must be lubricated

regularly if it is to operate flawlessly at all times.

ATTENTION: DISCONNECT COMPRESSED AIR

BEFORE MAINTENANCE WORK!

Keep the pneumatic devices clean.

Turn over the tool so that the compressed air con-

nection points upwards, and apply a few drops of

pneumatic equipment or motor oil SAE 10-20 into

the compressed air connection on the pneumatic

devices.

Press the trigger arm

to distribute the oil more

evenly. Hold a cloth or absorbent paper towel in

front of the exhaust air openings, and let the device

run in idle mode for a few seconds.

ATTENTION! EXCESS OIL IS BLOWN OUT. KEEP

THE DISCHARGE HOLE AWAY FROM PERSONS

AND OBJECTS.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 292193 PDTS 6.3 A1 Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info