Bedienungsanleitung Parkside IAN 292291 PBS 350 A1 (Seite 27 von 72) (Deutsch, Englisch, Holländisch, Französisch)

747882

Zoom out

Zoom in

Vorherige Seite

1/72

Nächste Seite

GB/IE20

• Press the clamping bar (25) down to ﬁx the parallel stop

(24) in place. In order to increase the clamping force of

the clamping bar (25), rotate it clockwise until the parallel

stop is suﬃciently ﬁxed in place.

• Make sure that the parallel stop (24) always runs parallel

to the Bandsaw blade (21).

10.3. Angled cuts (Fig. 17)

In order to execute angled cuts parallel to the Bandsaw

blade (21), it is possible to tilt the saw bench (7) forwards

from 0° - 45°.

• Undo locking handle (20) and wing nut (31).

• Tilt saw bench (7) forwards, until the desired angle is set

on the degree scale (17).

• Retighten the locking handle (20) and wing nut (31).

• Attention: With a tilted saw table (7), the parallel stop (24)

must always be ﬁtted to the right of the Bandsaw blade

(21) in the working direction. This prevents the workpiece

from slipping.

11. Transport

The machine must only be lifted and transported on its frame

or the frame plate. Never lift the machine at the safety de-

vices, the adjusting levers, or the sawing table.

During the transport the saw blade protection must be in the

lowest position and near the table.

Never raise at the table! Unplug the machine from the mains

during transport.

12. Working instructions

The following recommendations are examples of the safe use

of band saws.

The following safe working methods should be seen as an aid

to safety. They cannot be applied suitably completely or com-

prehensively to every use. They cannot treat every possible

dangerous condition and must be interpreted carefully.

• Connect the machine to a suction unit when working in

closed rooms. A suction device which conforms with commer-

cial regulations must be used for suction in commercial areas.

• Loosen the sawband when the machine is not in operation

(e.g. after ﬁnishing work). Attach a notice on the tension of

the saw band to the machine for the next user.

• Collect unused sawbands and store them safely in a dry

place. Check for faults (teeth, cracks) before use. Do not

use faulty sawbands!

• Wear suitable gloves when handling sawbands.

• All protective and safety devices must be securely mounted

on the machine before beginning work.

• Never clean the sawband or the sawband guide with a

hand-held brush or scraper while the sawband is running.

Resin-covered sawbands impair working safety and must

be cleaned regularly.

• For your own protection, wear protective glasses and hear-

ing protection. Wear a hairnet if you have long hair. Roll

up loose sleeves over the elbows.

• Always position the sawband guide as near the workpiece

as possible when working.

• Insure suﬃcient lighting in the work area and around the

machine.

• Always use the fence for straight cuts to keep the work-

piece from tipping or slipping away.

• When working on narrow workpieces with manual feed,

use the push stick.

• For diagonal cuts, place the saw bench in the appropriate

position and guide the workpiece on the fence.

• In order to cut dovetail tenons and teeth or wedges, bring

the saw table into the corresponding position on the an-

gle scale.

• For arced and irregular cuts, push the workpiece evenly

using both hands with the ﬁngers together. Hold the work-

piece with your hands on a safe area.

• Use a pattern for repeated arced or irregular cuts.

• Insure that the workpiece does not roll when cutting round

pieces.

Attention! After every new setting, we recommend performing

a test cut, in order to check the dimensional settings.

• With all cutting processes, the top saw band guide (5)

must be positioned as close as possible to the workpiece

(see 9.5).

• The workpiece must always be guided with both hands

and kept ﬂat against the saw table (7). This prevents the

Bandsaw blade (21) from jamming.

• Forward feeding should always take place with an even

pressure, which is just suﬃcient for the saw band to cut

through the material with ease without becoming blocked.

• Always use the parallel stop (24) for all cutting processes

that it can be used for.

• It is better to perform a cut in a single working step than

in multiple steps, which may require that the workpiece be

drawn back. However, if it is not possible to avoid drawing

the workpiece back then the band saw must be switched

oﬀ ﬁrst. Only draw the workpiece back once the Bandsaw

blade (21) has come to a standstill.

• When sawing, the workpiece must always be guided by

its longest side.

• Attention! When processing narrower workpieces it is es-

sential to use a Push stick. The Push stick (26) must always

be stored within reach, on the Push Stick retainer (48) pro-

vided for this purpose on the side of the saw.

12.1 Performing longitudinal cuts (Fig. 18)

Here, a workpiece is cut in its longitudinal direction.

• Position the longitudinal fence (24) on the left side (if pos-

sible) of the Bandsaw blade (21), in accordance with the

desired width.

• Lower the saw band guide (5) onto the workpiece (9.5).

• Switch on the saw (see 10.1).

• Press one edge of the workpiece against the longitudinal

fence (24) with the right hand, whilst the ﬂat side lies on

the saw bench (7).

• Slide the workpiece at an even feed rate along the longi-

tudinal fence (24) into the Bandsaw blade (21).

• Important: Long workpieces must be secured against tip-

ping at the end of the cutting process (e.g. with reel-oﬀ

stand, etc.)

12.2 Performing angled cuts (Fig. 17)

• Set saw bench to desired angle (see „Angled cuts“).

• Perform the cut as described under „Performing longitu-

dinal cuts“.

Parkside IAN 292291 PBS 350 A1 Seite 27

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info