Bedienungsanleitung Parkside IAN 298505 PDSP 1000 D4 (Seite 17 von 64) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

748055

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

17 GB/IE

cause silicosis with a grain size of 0.2 mm–

0.8 mm.

Ensure that the blasting material

is com-

pletely dry and that it is not too coarse.

Note: The maximum grain size is 0.8 mm.

Open the screw cap

of the blasting mate-

rial holder

by turning it counterclockwise.

Pour the desired amount of blasting material

into the blasting material holder

Ensure that the maximum holder contents do

not exceed 0.9 l.

Then close the screw cap

of the blasting

material holder

by turning it clockwise.

Ensure that the screw cap

is closed tightly.

Note on grain size of the blasting

material:

The bigger/the coarser the grain size of the blast-

ing material used, the coarser the contamination

you are trying to remove by using it. The blasting

material contained is small and is highly suitable

for removing materials such as ﬂash rust or impuri-

ties. The material surface is spared by using a small

blasting material and this only results in superﬁcial

wear. A coarser grain size for the blasting material,

which you can get in a specialist shop, is suitable

for coarser rust.

Caution: Observe the maximum grain size.

Assembling the collection bag

for sandblasting material

Use the screw clamp

included in the delivery

contents and a screwdriver to assemble the

collection bag

on the product.

Selecting and assembling an

attachment

First, select the attachment (

)

which is suitable for your work.

Place the attachment you have selected onto

the jet nozzle

and ensure that no air can

leak from the sides.

Using the air sand blaster gun

Prepare the material to be sandblasted by

degreasing and cleaning it.

Note: Dust and grease deposits signiﬁcantly

impair the result.

Carefully cover or mask everything which will

not be sandblasted.

The distance between the attachment and the

surface to be processed is crucial for the result.

Hold it as low as possible so that the blasting

material

can be collected by the collection

bag

The closer you go with the product to the work

piece, the smaller the blasting pattern and vice

versa.

If necessary, do a test run beforehand on a

work piece you no longer need. By doing so

you will ﬁgure out the correct distance/operat-

ing pressure and prevent excessive blasting.

Switching on:

Open the air passage by setting the rotary

control

to „1“.

Introduce the air sand blaster gun

to the

surface to be processed.

Activate the trigger

to operate the air sand

blaster gun

Switching oﬀ:

Release the trigger

to switch oﬀ the air

sand blaster gun

Set the rotary control

to „0“ to close the air

passage.

Disconnect the product from the compressed

air source after ﬁnishing work.

Note: First, remove the hose from the com-

pressed air source, and then remove the supply

hose from the product. Following these instruc-

tions will stop the supply pipe from twirling

around uncontrollably or recoiling.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Parkside IAN 298505 PDSP 1000 D4 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info