748074
29
Zoom out
Zoom in
Vorherige Seite
1/140
Nächste Seite
29
IEGB
1. Press the spindle locking button
(16) on the front side of the ma-
chine and keep it pressed down.
2. Use the combination wrench (27)
to loosen the cap nut (8) as much
as needed, so that the cutter can
be inserted.
3. Release the spindle locking but-
ton (16).
4. Insert the desired cutter into the
already mounted collet chuck
(13). The cutter shaft must be
pushed in at least 20 mm.
5. Use the combination wrench (27)
to tighten the cap nut (8) while
keeping the spindle locking but-
ton (16) pressed.
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Change collet chuck
All cutters of the 6-part cutter set included
in the delivery are provided with an 8-mm
cutter shaft.
Change the collet chuck for cutters with a
6-mm cutter shaft.
1. Press the spindle locking button (16) on
the front side of the machine and keep
it pressed down.
2. Screw off the cap nut (8) using the com-
bination wrench (
27).
3. Release the spindle locking button (16).
4. Take out the 8mm collet chuck (13) and
insert the 6mm collet chuck (22) and
the spring (37) included in the delivery
in the sequence shown in the diagram.
5. Screw the cap nut (8) loosely back on.
6. Insert a cutter as described above .
Tighten the cap nut only when a
cutter is inserted. The collet chuck
might get damaged.
Connecting the suction
adapter
You can reduce dust formation while you
work by connecting a dust suction system.
1. Fit the suction adapter (20) on the pro-
vided drill holes (
12) in the base-
plate (10).
2. Screw on the 2 recessed head screws
(21) from the bottom side of the base-
plate (10).
3. Fit the reducer part (30) on the suction
adapter if needed.
4. Connect the suction hose of a vacuum
cleaner to the suction adaptor (20).
The vacuum cleaner must be
suitable for the workpiece to be
processed. Use a special vacuum
cleaner if dusts with hazard for
health are created.
Mounting the parallel stop
1. Screw both screws out of the guide
bars (29).
2. Screw the guide bars (29) onto the par-
allel stop (24) using the spanner (27).
Adjust cutting depth
The switch has 6 levels:
0 - 5 - 10 - 15 - 20 - 25 mm
Before you begin to set the milling
depth, turn the rotary knob (2) until
the ne adjustment pin is unscre-
wed from the depth stop (17) by
approx. 5 mm.
29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Parkside IAN 304379 POF 1200 C2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info